Graco Inc 313516C important safety instructions Flush Spray Gun, Position Air Cap

Page 15

KEY

N Cylinder Air Inlet: accepts 1/4 in. (6.3 mm) O.D. tubing

P Atomization Air Inlet: 3/8 in, (9.5 mm) O.D. tubing

R Fan Air Inlet: 3/8 in. (9.5 mm) O.D. tubing

S Fluid Inlet: 1/4 npsm

T Fluid Outlet (circulating gun only): 1/4 npsm

Side Mounted Manifold Ports

N

T (or S)

S (or T)

FAN ATOM

CYL

ti8096a

RP

Bottom Mounted Manifold Ports

N

Setup

Flush Spray Gun

Before running any paint through the spray gun:

1.Flush the gun with a solvent that is compat- ible with the fluid to be sprayed, using the lowest possible fluid pressure and a grounded metal container.

2.Perform Pressure Relief Procedure; see page 18.

Position Air Cap

Air caps are factory-set with the alignment pin

(A)set to a vertical spray pattern. To change the air cap to a horizontal spray pattern, use a 1/6 in. hex wrench to unscrew the alignment pin (A) and relocate it to the horizontal spray pattern hole. When relocating the pin use low strength thread locker. Torque to 1.5-2.5 in-lb (0.2-0.3 N•m). Do not overtighten. Refer to FIG. 9.

R	FAN	ATOM	P
	FAN	ATOM
		CYL
T (or S)			S (or T)
T (or S)

ti8171a

A

Vertical Pattern

ti8097a

FIG. 8: Manifold Ports

Horizontal Pattern

ti8170a

ti8172a

FIG. 9: Position Air Cap

313516C

15

Image 15

Contents Automatic AirPro Spray Guns Important Safety InstructionsModels ContentsFire and Explosion Hazard Pressurized Equipment Hazard General Metal Applications Selection ChartsHvlp Guns High Wear ApplicationsWood Applications Gun SelectionProper Needle/Nozzle Selection Air CapsConventional Guns Air Flow Atomizing Air Fan AirAir Flow Maximum HVLP/Compliant inlet manifold pressure Circulating System InstallationVentilate Spray Booth Configure Gun and ManifoldGround System Install Air FittingsMount Gun Reciprocating Arm Rod MountStationary Support Retrofit Adapter Plate Mount Retrofit Adapter PlateSetup Connect Air LineConnect Fluid Hose Position Air Cap Flush Spray GunSpray Gun Adjust Spray PatternSuggested Starting Settings Atomization Fan Air psiAir Pressure Regulator Incorrect Pressure Relief ProcedureOperation Apply FluidDaily Gun Care Clean and Flush Gun General System MaintenanceTroubleshooting General TroubleshootingProblem Cause Solution Spray Pattern Troubleshooting Disassembly ServiceAlternate Fluid Control Shown Reassembly 17† 21† Alternate Fluid Control 20† 22† 36† 24a 25a PartsGasket Repair Kits General Metal ApplicationsNozzle Wood Applications High Wear ApplicationsPart Description Qty Manifold with bottom fluid portsPart No C342 Side Fluid Ports and Fan Adjustment ValveNot shown, optional size Not sold separately Part No only Description Qty106 Accessories Count Carton Pack Description Hvlp Pressure Verification KitInline Fluid Filter 24B707 Spray Tip FiltersDimensions Manifold Models 288217 or 288218, All Gun ModelsManifold Model 288221, All Gun Models Manifold Model 288160 or 288211, All Gun Models Manifold Model 288223 or 24C342, All Gun ModelsMounting Hole Layouts 23.4 mm 10.2 mm 53.3 mm 50 in .7 mm Mounting hole 216 23.4 mm 10.2 mm 27.9 mm 375 in .5 mm Mounting hole Retrofit Adapter Plate Cylinder Air Fluid Pressure Air Pressure Msec to fully Technical DataTriggering Speed Sound DataGraco Standard Warranty Graco InformationGraco Headquarters Minneapolis