I.C.T.C. Holdings Corporation 1150GSD Flushing the Unit AT Shutdown Or Color Change

Page 9

FLUSHING THE UNIT AT SHUTDOWN

OR COLOR CHANGE

If shutting down for a short period of time, it is sufficient to trigger the gun to relieve pressure. Then set the safety lock on gun to "locked" position with the gun locked closed and immerse the gun in a container of the correct thinner for the paint you are spraying.

1.Remove spray tip from gun.

2.Turn pressure control knob counter clockwise to low pressure setting. Only

use sufficient pressure to allow material to move through the sprayer. DO NOT operate at or near full pressure.

3.Remove siphon assembly from paint container.

4.Trigger gun, back into paint container, until unit runs dry.

NOTE: Pump and spray hose will continue to contain paint. This paint may be recovered by placing prime hose into paint container and draining the remainder while re-priming with cleaning fluid. See step 5* and 6*.

5.Place siphon assembly in container of correct thinner, for the spray product being used,, and prime the pump as shown in step 13, of "Spraying". *See

special notes from step 4. Allow thinner to circulate back into the container for a few minutes to flush the prime valve.

6.Close prime valve.

7.Trigger gun into paint container until thinner comes through. *See special notes from step 4. Re-direct flow into waste container and continue spraying until thinner runs clear. Heavily soiled thinners may have to be changed to complete cleaning job.

8.Lift siphon assembly and allow pump to run dry.

9.Repeat procedure using a gallon of H.E.R.O. Equipment Wonder Wash solution. If not using Wonder Wash, unit must not be stored with water. Only store with a non corrosive material ( Paint thinner, solvent ).

10.Switch unit "off" and trigger gun to relieve remaining pressure.

11.Remove and rinse gun handle filter in correct thinner.

SPECIAL STORAGE INSTRUCTIONS

In areas where the sprayer is NOT used 12 months of the year, special preparations must be used for winter or off season storage. Because solvents evaporate quickly, they should not be used for long term storage. A petroleum based solution ( solvent and oil ) should be used as an extended storage material. DO NOT allow storage solution to freeze in the sprayer.

H.E.R.O. Equipment Wonder Wash, available from your H.E.R.O. distributor, will provide the added cleaning benefits of solvent at a much lower cost. Suitable as a short term ( 1-2 days ) storage solution only

SPECIAL NOTES AND INSTRUCTIONS

H.E.R.O. INDUSTRIES

8

1150GSD MANUAL - “B” VERSION

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Version Beginning AT Serial Number Airless Spray EquipmentR.O. Warranty Table of Contents Important Safety PrecautionsAlways Always R.O. Airless Spray PaintingInstructions Setting UP to SprayHydrapulse B Version Beginning AT Serial Number E R a T I N GAlways Paint Straining Special Notes and Instructions Flushing the Unit AT Shutdown Or Color ChangeAirless Spray Painting GAS EngineAirless Spray Painting Suggestions and Technique Suggestions and TechniqueSpray TIP Selection Spray TIP Replacement TroubleshootingTIP Size For Application Orifice SizeR.O. Industries 1150GSD Manual B Version Paint Intake Valve Assembly REF# Hydraulic Intake Valve REF# 66Hydraulic Outgo Valve REF# 74, PART# 4-27C Prime Valve REF# 36, PART# Paint Outgo Valve REF# 26, PART# 4-611CSituation Gasoline Engine Wont START/RUN No PRESSURE, Blue Hydraulic Fluid in Paint Troubleshooting Sprayer does not Prime with Paint Spray Pattern is Spotty or Uneven Hydrapulse Membrane ReplacementRemoval Replacement of Intake SeatTools Required Piston RepairsSpecial Notes Outgo Valve REF# Prime Valve Repairs O L S Required Pressure Control ValveO L S Accessories Parts ListZIP TIP INSERT, Available in the Following Sizes Parts ListDescription QTY AssyKIT Outgo Parts Industries 1150GSD Manual B Version Drive Parts Decals 1150GSD Parts Schematic Manual B Version
Top Page Image Contents