I.C.T.C. Holdings Corporation 1150GSD Instructions, E R a T I N G, Setting UP to Spray

Page 6

inconvenience and mess of overspray. You are spraying paint, not air, and the paint is driven to the painting surface in a clean, fan shaped spray which penetrates all cracks and corners. To attain these results, you must adjust the pressure as low as possible. We recommend that you become familiar with your H.E.R.O. unit. Discuss with your dealer the useful accessory items he has to offer - various types of tips, extension poles for hard to reach areas, extra hose, etc. Use of accessory items is often the difference between a good job and an excellent one!

INSTRUCTIONS

WARNING

1997

HYDRAPULSE “B” VERSION BEGINNING AT SERIAL NUMBER

140056

O P E R A T I N G

Do not attempt to operate this machine until you have read and understood all safety precautions and operating instructions. Equipment and chemicals when used improperly can be dangerous.

Your H.E.R.O. airless sprayer has been fully factory tested prior to shipment.

BEFORE STARTING YOUR H.E.R.O. PUMP....

CHECK to ensure that the shipping seal has been removed from under the cap on the hydraulic tank. Hydraulic tank should be at least 3/4 full of H.E.R.O. LVO hydraulic fluid.

CHECK all fittings and connections in the pump system, hose, and gun to ensure that they are tight. CHECK to ensure that there is a spray tip in the gun, and that the tip is the correct size for the coating you are to spray. ( There are various tips available, for each type of coating or configuration. See " Airless Spray Tip " on page 11 , for proper tip selection.

CHECK to ensure that you have H.E.R.O. strainer bags, H.E.R.O. Wonder Wash, appropriate thinner for the paint, a waste container, and any other accessories you may require for the job.

READ THIS MANUAL THOROUGHLY.

READ THE HONDA ENGINE MANUAL SUPPLIED WITH THE UNIT. FOLLOW ALL THEIR RECOMMENDED PROCEDURES FOR “START-UP” AND OPERATION

SETTING UP TO SPRAY

1. Remove unit from shipping carton.

2.Attach intake siphon assembly (ref# 1) to intake elbow (ref# 8). The intake elbow provides a swiveling connection during assembly only. Two wrenches are required to tighten these fittings. When sufficiently

H.E.R.O. INDUSTRIES

5

1150GSD MANUAL - “B” VERSION

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Airless Spray Equipment Version Beginning AT Serial NumberR.O. Warranty Important Safety Precautions Table of ContentsAlways R.O. Airless Spray Painting AlwaysHydrapulse B Version Beginning AT Serial Number Setting UP to SprayInstructions E R a T I N GAlways Paint Straining Flushing the Unit AT Shutdown Or Color Change Special Notes and InstructionsGAS Engine Airless Spray PaintingSuggestions and Technique Airless Spray Painting Suggestions and TechniqueSpray TIP Selection TIP Size For Application TroubleshootingSpray TIP Replacement Orifice SizeR.O. Industries 1150GSD Manual B Version Paint Intake Valve Assembly REF# Hydraulic Intake Valve REF# 66Hydraulic Outgo Valve REF# 74, PART# 4-27C Paint Outgo Valve REF# 26, PART# 4-611C Prime Valve REF# 36, PART#Situation Gasoline Engine Wont START/RUN No PRESSURE, Blue Hydraulic Fluid in Paint Troubleshooting Sprayer does not Prime with Paint Hydrapulse Membrane Replacement Spray Pattern is Spotty or UnevenReplacement of Intake Seat RemovalPiston Repairs Tools RequiredSpecial Notes Outgo Valve REF# Prime Valve Repairs Pressure Control Valve O L S RequiredAccessories Parts List O L SParts List ZIP TIP INSERT, Available in the Following SizesDescription QTY AssyKIT Outgo Parts Industries 1150GSD Manual B Version Drive Parts Decals 1150GSD Parts Schematic Manual B Version
Top Page Image Contents