Grizzly G9749 owner manual Accessories, H5685-4Rotary Table, G1076-52-PC. Clamping Kit

Page 27

SECTION 5: ACCESSORIES

G2500—20-PC Regular Sanding Drum Set This kit consists of 5 drums in popular 1⁄2" x 1⁄2", 3⁄4"

x1", 1"x 1", 11⁄2" x 11⁄2", and 2" x 11⁄2" sizes. Comes with 50, 80 and 120 grit sizes for each drum.

Figure 24. Model G2500 20-PC Sanding Drum

Set.

G8865—Cobalt Alloy Drill Bits 13-PC. Set G8866—Steelex®Cobalt Alloy Drill Set 21-PC G8867—Steelex®Cobalt Alloy Drill Set 29-PC

Cobalt Alloy bits will retain their edge sharpness longer than normal HSS bits, resulting in a signifi- cant saving of time and money in the workshop. Includes a heavy-gauge steel index case for storing. G8865: 1⁄16" -1⁄4"; G8866: 1⁄16"- 3⁄8"; G8867: 1⁄16"-1⁄2".

Figure 25. Model G8865 13-PC Alloy Drill Bits.

G9749 Variable Speed Drill Press

H5685—4"Rotary Table

The perfect rotary table for all you model makers and those doing smaller precision work. Comes with clamping kit.

Figure 26. H5685 4" Rotary Table.

G1076—52-PC. Clamping Kit

This clamping kit includes 24 studs, 6 step block pairs, 6 T-nuts, 6 flange nuts, 4 coupling nuts, and 6 end hold-downs. The rack is slotted so it can be mounted close to the machine for easy access.

Figure 27. G1076 52-PC. Clamping Kit.

-25-

Image 27

Contents Model G9749 Variable Speed Drill Press Page Table of Contents Introduction ForewordContact Info Machine Data Sheet Other Related Information Identification G9749 Variable Speed Drill Press Safety Instructions for Machinery Additional Safety for Drill Presses Circuit Requirements Circuit Requirements110/220V Operation Amperage Draw110V Operation GroundingExtension Cords 220V OperationSite Considerations SetupSetup Safety Items Needed for SetupTo unpack and move the drill press Unpacking LiftingMounting to Shop Floor Bolting to Concrete FloorsTo mount the drill press to the floor Contents Figure Qty Inventory Clean UpComponents and Hardware Needed Qty AssemblyTo install the rapid downfeed handles To install the table crank handleTo test run the machine Test Run Spindle Break-InInstalling Drill Chuck To install the drill chuck onto the arborOperations To remove a drill bit from the chuck Installing/Removing Drill BitsTo install a drill bit into the chuck Changing SpeedsUsing the Drill Bit Speed Chart Choosing SpeedsLubrication Suggestions Drilling Quill TravelTo use the quill lock To use the rapid downfeed control To use the fine downfeed controlTo use the depth gauge and depth stop To rotate the headstock Table AdjustmentsTo adjust table height and rotation Headstock RotationTo remove the arbor and chuck from the spindle Removing/Installing Arbor and ChuckTo remove the chuck from the arbor To install the arbor into the spindle with the drawbarAccessories H5685-4Rotary TableG1076-52-PC. Clamping Kit Lubrication MaintenanceSchedule Unpainted Cast IronSymptom Possible Cause Possible Solution ServiceAbout Service TroubleshootingDrill Operations Electrical Components G9749 switch wiringWiring Diagram Headstock Parts Breakdown Headstock Components Parts Breakdown Variable Speed Parts Breakdown Base Parts Breakdown Description Parts ListFlat Washer 1/4 403 401 405 404 400 402 406 Label PlacementWarranty and Returns Page Page