Grizzly G0758 owner manual Lifting & Placing, To lift machine and place it in position

Page 18

Lifting & Placing

The Model G0758 mill/drill can be mounted to a workbench or the Model T26612 optional stand (see Figure 9). The optional stand is specifically designed for Model G0758 and comes with pre- drilled mounting holes.

Figure 9. Model T26612 optional stand for

Model G0758.

HEAVY LIFT!

Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a forklift (or other lifting equipment) rated for weight of this machine.

-16-

To lift machine and place it in position:

1.Place shipping crate next to workbench (or stand) where machine will be placed.

2.Use vertical handwheel to raise headstock as far as possible (see Figure 10). Lock head- stock in place to avoid sudden shifts during lifting.

Lifting

Sling

Vertical

Handwheel

Figure 10. Headstock positioned for lifting.

3.Hang sling from forklift fork and place it under headstock, as shown in Figure 10. DO NOT place sling over any controls or against any components that may be damaged from the force required for lifting.

4.Unbolt machine from pallet. Have an assis- tant on the ground steady machine to prevent it from swinging and lift it slightly off the pallet with forklift.

5.Carefully place machine onto workbench or optional stand.

6.Mount machine to workbench following instructions in Bench Mounting on Page 17 or to stand following instructions included with stand.

Model G0758 (Mfd. Since 2/14)

Image 18

Contents Model G0758 MILL/DRILL Page Table of Contents Introduction Machine Description Manual AccuracyContact Info Identification Right side identification Model G0758 Mfd. Since 2/14Controls Components Machine Data Sheet Table Info Safety Safety Instructions for MachineryPage Additional Safety for Mills/Drills Full-Load Current Rating Power SupplyAvailability 110V Circuit RequirementsMinimum Gauge Size 16 AWG Grounding & Plug RequirementsExtension Cords 50 ftUnpacking SetupNeeded for Setup Description QtyInventory Inventory Figure QtyCleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Lifting & Placing To lift machine and place it in positionDiameter of Mounting Hardware AssemblyBench Mounting WorkbenchJoining Drill Chuck Arbor Lubricating Mill/DrillTo join drill chuck and arbor Test Run Inspections Adjustments Spindle Break-InOperations Operation OverviewUsing Fine Downfeed Using Coarse DownfeedUsing DRO Downfeed ControlsTilting Headstock Headstock MovementRaising/Lowering Headstock Tools Needed QtyAxis Handwheel Table TravelGraduated Dials Tool Needed QtyInstalling/Removing Tooling Installing ToolingTo install tooling Determining Spindle Speed Spindle SpeedRemoving Tooling To remove toolingAccessories T26612-Optional Stand for Model G0758Schedule MaintenanceCleaning Protecting LubricationTable and Column Ways Axis LeadscrewsTo lubricate Z-axis leadscrew To lubricate table leadscrews Table LeadscrewsHeadstock Gears To lubricate headstock gearsReplacing DRO Battery Quill Outside SurfaceQuill Rack Service TroubleshootingSymptom Possible Cause Possible Solution Symptom Possible Cause Possible Solution Adjusting Gibs Adjusting Leadscrew BacklashBrush Replacement To inspect and replace motor brushesWiring Wiring Safety InstructionsG0758 Wiring Overview Wiring overview Model G0758 Mfd. Since 2/14G0758 Wiring GNDRear panel Parts ColumnDescription Electrical Box Headstock Description Chip Guard Labels & Cosmetics Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns