Grizzly G0758 owner manual Introduction, Machine Description Manual Accuracy, Contact Info

Page 4

INTRODUCTION

Machine Description

 

Manual Accuracy

 

 

 

 

 

 

The Model G0758 is a high-precision mill/drill with

a600 Watt (3⁄4 HP) high-torque, low noise motor, with low speed gearing for maximum torque in the lowest RPM range.

This mill/drill has a spindle-to-table distance of 9" with a 131⁄4" swing. It has an R-8 spindle size and features manual downfeed controls with a variable spindle speed range from 50–2000 RPM. DRO's for both the spindle speed and spindle downfeed stroke allow precise operation. The headstock tilts 45° left/right and moves in the Z-axis along dove- tailed ways for maximum precision.

The large 51⁄2" x 1911⁄16" table features manual 13" (X-axis) and 51⁄2" (Y-axis) travel. All table move- ment is along precision-ground dovetailed ways. An optional stand (Model T26612) is available for purchase at www.grizzly.com.

Contact Info

We stand behind our machines. If you have any questions or need help, use the information below to contact us. Before contacting, please get the serial number and manufacture date of your machine. This will help us help you faster.

Grizzly Technical Support 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663

Email: techsupport@grizzly.com

We want your feedback on this manual. What did you like about it? Where could it be improved? Please take a few minutes to give us feedback.

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: manuals@grizzly.com

-2-

We are proud to provide a high-quality owner’s manual with your new machine!

We made every effort to be exact with the instruc- tions, specifications, drawings, and photographs contained inside. Sometimes we make mistakes, but our policy of continuous improvement also means that sometimes the machine you receive will be slightly different than what is shown in the manual.

If you find this to be the case, and the difference between the manual and machine leaves you confused about a procedure, check our website for an updated version. We post current manuals and manual updates for free on our website at www.grizzly.com.

Alternatively, you can call our Technical Support for help. Before calling, please write down the Manufacture Date and Serial Number stamped into the machine ID label (see below). This infor- mation helps us determine if updated documenta- tion is available for your machine.

Manufacture Date

Serial Number

Model G0758 (Mfd. Since 2/14)

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model G0758 MILL/DRILL Page Table of Contents Machine Description Manual Accuracy IntroductionContact Info Identification Right side identification Model G0758 Mfd. Since 2/14Controls Components Machine Data Sheet Table Info Safety Safety Instructions for MachineryPage Additional Safety for Mills/Drills Power Supply AvailabilityFull-Load Current Rating 110V Circuit RequirementsGrounding & Plug Requirements Extension CordsMinimum Gauge Size 16 AWG 50 ftSetup Needed for SetupUnpacking Description QtyInventory Inventory Figure QtyBefore cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Lifting & Placing To lift machine and place it in positionAssembly Bench MountingDiameter of Mounting Hardware WorkbenchLubricating Mill/Drill Joining Drill Chuck ArborTo join drill chuck and arbor Test Run Inspections Adjustments Spindle Break-InOperations Operation OverviewUsing Coarse Downfeed Using DROUsing Fine Downfeed Downfeed ControlsHeadstock Movement Raising/Lowering HeadstockTilting Headstock Tools Needed QtyTable Travel Graduated DialsAxis Handwheel Tool Needed QtyInstalling Tooling Installing/Removing ToolingTo install tooling Spindle Speed Removing ToolingDetermining Spindle Speed To remove toolingAccessories T26612-Optional Stand for Model G0758Maintenance Cleaning ProtectingSchedule LubricationAxis Leadscrews Table and Column WaysTo lubricate Z-axis leadscrew Table Leadscrews Headstock GearsTo lubricate table leadscrews To lubricate headstock gearsQuill Outside Surface Replacing DRO BatteryQuill Rack Troubleshooting ServiceSymptom Possible Cause Possible Solution Symptom Possible Cause Possible Solution Adjusting Gibs Adjusting Leadscrew BacklashBrush Replacement To inspect and replace motor brushesWiring Wiring Safety InstructionsG0758 Wiring Overview Wiring overview Model G0758 Mfd. Since 2/14G0758 Wiring GNDRear panel Parts ColumnDescription Electrical Box Headstock Description Chip Guard Labels & Cosmetics Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns
Top Page Image Contents