Grizzly G0758 owner manual Needed for Setup, Unpacking, Description Qty

Page 14

SECTION 3: SETUP

This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with controls and operations before starting machine!

Wear safety glasses during

entire setup process!

HEAVY LIFT!

Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a forklift (or other lifting equipment) rated for weight of this machine.

Keep hair, clothing, and jewelry away from mov- ing parts at all times. Entanglement can result in death, amputation, or severe crushing injuries!

Needed for Setup

The following are needed to complete the setup process, but are not included with machine.

Description

 

Qty

Additional People

1

Safety Glasses

1

Cleaner/Degreaser (Page 14)

As Needed

Disposable Shop Rags

As Needed

Forklift

1

• Lifting Sling (rated for at least 300 lbs.).

..... 1

Mounting Hardware (Page 17)....

As Needed

Brass Hammer (Page 26)

1

Mineral Spirits (Page 18)

As Needed

Wood Block (Page 18)

1

Unpacking

Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and inspect it. If you discover any damage, please call us immediately at (570) 546-9663 for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi- tion of your shipment, inventory the contents.

SUFFOCATION HAZARD!

Keep children and pets away from plastic bags or packing materials shipped with this machine. Discard immediately.

-12-

Model G0758 (Mfd. Since 2/14)

Image 14
Contents Model G0758 MILL/DRILL Page Table of Contents Contact Info IntroductionMachine Description Manual Accuracy Identification Right side identification Model G0758 Mfd. Since 2/14Controls Components Machine Data Sheet Table Info Safety Safety Instructions for MachineryPage Additional Safety for Mills/Drills Full-Load Current Rating Power SupplyAvailability 110V Circuit RequirementsMinimum Gauge Size 16 AWG Grounding & Plug RequirementsExtension Cords 50 ftUnpacking SetupNeeded for Setup Description QtyInventory Inventory Figure QtyBasic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Lifting & Placing To lift machine and place it in positionDiameter of Mounting Hardware AssemblyBench Mounting WorkbenchTo join drill chuck and arbor Joining Drill Chuck ArborLubricating Mill/Drill Test Run Inspections Adjustments Spindle Break-InOperations Operation OverviewUsing Fine Downfeed Using Coarse DownfeedUsing DRO Downfeed ControlsTilting Headstock Headstock MovementRaising/Lowering Headstock Tools Needed QtyAxis Handwheel Table TravelGraduated Dials Tool Needed QtyTo install tooling Installing/Removing ToolingInstalling Tooling Determining Spindle Speed Spindle SpeedRemoving Tooling To remove toolingAccessories T26612-Optional Stand for Model G0758Schedule MaintenanceCleaning Protecting LubricationTo lubricate Z-axis leadscrew Table and Column WaysAxis Leadscrews To lubricate table leadscrews Table LeadscrewsHeadstock Gears To lubricate headstock gearsQuill Rack Replacing DRO BatteryQuill Outside Surface Symptom Possible Cause Possible Solution ServiceTroubleshooting Symptom Possible Cause Possible Solution Adjusting Gibs Adjusting Leadscrew BacklashBrush Replacement To inspect and replace motor brushesWiring Wiring Safety InstructionsG0758 Wiring Overview Wiring overview Model G0758 Mfd. Since 2/14G0758 Wiring GNDRear panel Parts ColumnDescription Electrical Box Headstock Description Chip Guard Labels & Cosmetics Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns