Hitachi Koki USA DH 24PC instruction manual HOW to USE, Selecting the driver bit, Switch operation

Page 12

Push button

Fig. 6

Fig. 7

English

bits which have 6-17/32" (166 mm), 6-19/64" (160 mm) and 4-21/64" (110 mm) overall length.

◯Dump particles after every two or three holes when drilling.

◯Please replace the drill bit after removing dust collector (B).

8.Selecting the driver bit

Screw heads or bits will be damaged should an inappropriate bit for the screw diameter be employed to drive in the screws.

9.Confirm the direction of bit rotation (Fig. 5)

The bit rotates clockwise (viewed from

the rear side) by pushing the R-side of R

the reversing switch lever. The L-side of the lever is pushed to turn the bit

counterclockwise.L

R

Lever

L

L

Fig. 5

HOW TO USE

CAUTION:

◯To prevent accidents, make sure to turn the switch off and disconnect the plug from the receptacle when the drill pits and other various parts are installed or removed. The power switch should also be turned off during a work break and after work.

Change Lever

1. Switch operation

The rotation speed of the drill bit can be controlled steplessly by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the switch is pulled more. To turn the switch OFF, release the trigger switch to its original position.

2. Rotation + Striking

This rotary hammer can be set to rota- tion and striking mode by pressing the push button and turning the change le-

ver to mark. (Fig. 6)

(1) Mount the drill bit.

(2) Pull the trigger switch after applying the drill bit tip to the drilling position (Fig. 7)

(3)Pushing the rotary hammer forcibly is not necessary at all. Pushing slightly so that drill dust comes out gradually is just sufficient.

12

Image 12

Contents DH 24PC Manual DE Instrucciones E Instrucciones DE SeguridadContents Meanings of Signal Words Important InformationSafety General Safety RulesEnglish Keep all screws, bolts and covers tightly in place Specific Safety Rules and Symbols Do not wipe plastic parts with solventDouble Insulation for Safer Operation Specifications Functional Description Name of Parts Assembly and Operation ApplicationsPrior to Operation Installation of dust cup or dust col Lector B Optional accessoriesMounting the drill bit Fig HOW to USE Switch operationSelecting the driver bit Confirm the direction of bit rotation FigWhen driving machine screws Fig Rotation onlyWhen driving wood screws Fig Striking onlyUsing depth gauge Fig HOW to USE the Core BIT for Light Load How to bore FigMounting Dismounting. Fig Maintenance and Inspection Accessories Standard AccessoriesDrill Bit Taper shank and taper shank adaptor Knock-in anchor Striking only Outer wedge type with the female screw Inner wedge type with the headless screwOuter wedge type with Female screw Inner wedge type with Headless screwGuide plate Demolishing operation Striking onlyGroove digging and edging Striking only Grooving Striking onlyDrilling holes Rotation only Driving Screws Rotation only Phillips Driver BitDust cup and Dust collector B Informations Importantes Signification DES Mots D’AVERTISSEMENTSecurite Regles Generale DE SecuriteConserver CES Instructions Français Utiliser l’outil correct Regles DE Securite Specifiques ET Symboles Ne pas essuyer les parties en plastique avec du solvantDouble Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES Parties4400/min Poids Lbs 2,4 kg Avant L’UTILISATION Precaution Montage du foret de perçage FigUtilisation Sélection de la mèche pour visseuseVérifiez la direction de rotation de La mèche Fig Fonctionnement de l’interrupteurRotation + frappe Rotation seulementLors du vissage des vis machine Fig Enfoncement de vis à bois FigPercussion uniquement Utilisation de la quenouille FigComment Utiliser LA Couronne Pour UNE Charge Legere MontagePerçage Fig Démontage FigEntretien ET Inspection Accessoires Accessoires StandardVendus séparément Foret de perçage queue conique et raccord de queue coniqueAncrage de chasse Percussion uniquement Cône en a 303619Type à cale extérieure avec vis femelle Type à cale intérieure avec vis sans têtePerçage de trou à large diamètre rotation + frappe Plaque centrale de guidage Travail de démolissage Percussion uniquementCreusage de rainures Percussion uniquement Perçage de trous rotation seulement Vis d’entraînement rotation uniquement Embout de vissage PhillipsCapuchon anti-poussière et collecteur à poussière B Información Importante Significado DE LAS Palabras DE SeñalizaciónSeguridad Normas Generales DE SeguridadGuarde Estas Instrucciones Eléctrica puede resultar en una lesión seria Utilice la herramienta correcta Normas Y Símbolos Específicos DE Seguridad Maneje con cuidado las herramientas eléctricas¡GUARDE Este Manual DE Instrucciones Donde Aislamiento Doble Para Ofrecer UNA Operación MÁS SeguraDescripción Funcional NomenclaturaEspecificaciones 4400/min Peso Lbs 2,4 kgMontaje Y Operación AplicacionesAntes DE LA Operación Montaje de la broca Fig PrecauciónComo SE USA Selección de la broca destornilladorConfirmar la dirección de rotación De la broca Fig Operación del conmutadorRotación + golpeteo Rotación solamenteCuando coloque tornillos para metal Fig Atornillando tornillos para madera FigPercusión solamente Modo de usar el tope FigModo DE Usar LA Barrena Tubularpara Cargas Ligeras MontajeModo de taladrar Fig Desmontaje FigMantenimiento E Inspección Accesorios Accesorios EstándarBroca de taladro vástago cónico y adaptador cónico Ancla de martillar Percusión solamente Tipo de reborde exterior con tornillo hembra Tipo de reborde interior con tornillo sin cabezaPlaca guia Trabajo de roturación Percusión solamenteExcavar, ranuado y rebordes Percusión solamente Ranurado Percusión solamentePerforación rotación solamente Colocación de tornillos rotación solamente Broca para tornillos PlillipsCopa de polvo y colector de polvo B Page Page Cord Clip Cord Armor Kestrel Road Mississauga on L5T 1Z5