Ryobi HD1830 manual General Safety Rules, Work Area, Electrical Safety, Personal Safety

Page 3

GENERAL SAFETY RULES

WARNING

Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Do not abuse the cord. Never use the cord to carry the charger. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged cords im- mediately. Damaged cords may create a fire.

A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.

Use battery operated tool only with specifically designated battery pack. Use of any other batteries may create a risk of fire.

Use battery only with charger listed.

MODEL BATTERY CHARGER

HD1830 130255004 1423701

PERSONAL SAFETY

Stay alert, watch what you are doing and use com- mon sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alco- hol, or medication. A moment of inattention while oper- ating power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jew- elry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jew- elry, or long hair can be caught in moving parts.

Avoid accidental starting. Be sure switch is in the locked or off position before inserting battery pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch on invites acci- dents.

Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

Use clamps or other practical way to secure and sup- port the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

Do not force tool. Use the correct tool for your appli- cation. The correct tool will do the job better and safer at the rate for which it is designed.

Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is danger- ous and must be repaired.

Disconnect battery pack from tool or place the switch in the locked or off position before making any ad- justments, changing accessories, or storing the tool. Such preventive safety measures reduce risk of starting the tool accidentally.

Store idle tools out of reach of children and other un- trained persons. Tools are dangerous in the hands of untrained users.

When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire.

Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control.

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool.

Keep the tool and its handle dry, clean and free from oil and grease. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based prod- ucts, or any strong solvents to clean your tool.

Page 3

Image 3
Contents Save this Manual for Future Reference Operators ManualIntroduction Table of ContentsWork Area General Safety RulesElectrical Safety Personal SafetyAdditional Rules for Safe Operation Specific Safety RulesService Important Rules for Battery ToolsImportant Safety Instructions for Charger Symbol Name DESIGNATION/EXPLANATION SymbolsInstructions SpecificationsUnpacking ApplicationsFeatures Auxiliary Handle AssemblyDepth Gauge ROD Switch Trigger BIT Storage Area Battery Pack Adjustments Adjusting the Auxiliary Handle AssemblyAdjusting the Depth Gauge ROD Adjusting the Torque Wrong Changing the BIT RotationInserting Bits Removing BitsLED Function of Charger OperationCharging Your DRILL-DRIVER To ChargeReversible Turning ON/OFF the Hammer DrillThree Speed Gear Train Electric Brake To Install Battery PackTo Remove Battery Pack BIT StorageDrilling Maintenance Removing the ChuckTightening the Chuck Disposal of the Exhausted Battery Battery Pack Preparation for RecyclingBatteries Service Model NO. and Serial no