Ryobi HD1830 manual Important Safety Instructions for Charger

Page 5

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER

WARNING:

Read and understand all instructions. Failure to fol- low all instructions listed below, may result in electric shock, fire and/or serious personal injury.

Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped battery immediately. Failure to heed this warning can result in serious personal injury.

Save these instructions. This manual contains impor- tant safety and operating instructions for charger.

Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, and product using battery charger. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

CAUTION: To reduce risk of injury, charge only nickel- cadmium type rechargeable batteries. Other types of batteries may burst causing personal injury and dam- age. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not expose charger to wet or damp conditions. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

To reduce risk of damage to charger body and cord, pull by charger plug rather than cord when discon- necting charger. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

c.That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet)

25'

50'

100'

Cord Size (AWG)

16

16

16

Note: AWG = American Wire Gage

Do not operate charger with a damaged cord or plug. If damaged, have replaced immediately by a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incor- rect reassembly may result in a risk of electric shock or fire. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

To reduce the risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Disconnect charger from power supply when not in use. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instruc- tions also. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

WARNING:

Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. Following this rule will reduce the risk of serious personal injury.

Do not abuse cord. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp edges. Following this rule will reduce the risk of electric shock or fire.

An extension cord should not be used unless abso- lutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:

a.That pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b.That extension cord is properly wired and in good electrical condition; and

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to cause cancer, birth defects or other repro- ductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

SAVE THESE INSTRUCTIONS

Page 5

Image 5
Contents Save this Manual for Future Reference Operators ManualIntroduction Table of ContentsElectrical Safety General Safety RulesPersonal Safety Work AreaService Specific Safety RulesImportant Rules for Battery Tools Additional Rules for Safe OperationImportant Safety Instructions for Charger Symbol Name DESIGNATION/EXPLANATION SymbolsUnpacking SpecificationsApplications InstructionsDepth Gauge ROD FeaturesAuxiliary Handle Assembly Switch Trigger BIT Storage Area Battery Pack Adjusting the Depth Gauge ROD AdjustmentsAdjusting the Auxiliary Handle Assembly Adjusting the Torque Inserting Bits Changing the BIT RotationRemoving Bits WrongCharging Your DRILL-DRIVER OperationTo Charge LED Function of ChargerReversible Turning ON/OFF the Hammer DrillThree Speed Gear Train To Remove Battery Pack To Install Battery PackBIT Storage Electric BrakeDrilling Tightening the Chuck MaintenanceRemoving the Chuck Batteries Disposal of the Exhausted BatteryBattery Pack Preparation for Recycling Service Model NO. and Serial no