Ryobi TS1301 warranty Dust BAG

Page 13

ASSEMBLY

■Depress the spindle lock button and rotate the blade bolt until the spindle locks. See Figure 10.

■Using the wrench provided, loosen and remove the blade bolt.

NOTE: The blade bolt has left hand threads. Turn blade bolt clockwise to loosen.

■Remove outer blade washer. Do not remove inner blade washer.

■Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade.

WARNING:

If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly.

■ Fit saw blade inside lower blade guard and onto spindle.

The blade teeth point downward at the front of saw as

shown in figure 11.

SPINDLE LOCK

SWITCH

TRIGGER

Fig. 10

LOWER

BLADE

GUARD

CAUTION:

Always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. The direction of blade rotation is also stamped with an arrow on the upper blade guard.

■ Replace outer blade washer. The double "D" flats on the

blade washers align with the flats on the spindle.

■ Depress spindle lock button and replace blade bolt.

NOTE: The blade bolt has left hand threads. Turn blade

bolt counterclockwise to tighten.

■ Tighten blade bolt securely.

■ Replace the lower blade guard and blade bolt cover.

BLADE

BOLT COVER

TO

LOOSEN

 

blade

lowersecurely.

Restore and

screw

 

use

guardtightenbefore

 

FLAT (S)

ON SPINDLE

Restore lower blade guard and securely tighten screw before use.

■ Replace screw B and tighten securely.

■ Retighten screw A securely.

■ Replace wrench in storage area.

WARNING:

Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage spindle lock button when blade is rotating.

DUST BAG

See Figure 12.

A dust bag is provided for use on your miter saw. It fits over the exhaust port on the upper blade guard. To install it, remove dust guide from exhaust port. Then, squeeze the two metal clips to open the mouth of the bag and slide it on the exhaust port. Release the clips. The metal ring in the bag should lock in between the grooves on the exhaust port.

To remove the dust bag for emptying, simply reverse the above procedure.

TO

 

BLADE

 

 

TIGHTEN

 

 

BLADE BOLT

OUTER BLADE WASHER

 

WITH DOUBLE "D" FLATS

Fig. 11

 

DUST BAG

METAL CLIPS

EXHAUST

PORT

Fig.812

4

Page

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Thank YOU for Buying a Ryobi Miter SAW Save this Manual for Future ReferenceTable of Contents Rules for Safe Operation Symbol Meaning Safety Alert SymbolDouble Insulation Read ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Additional Rules For Safe Operation For Miter Saws Glossary of Terms for Woodworking Unpacking and Checking Contents Features Spindle Lock Button Miter Lock HandleTrigger Lock Positive Stops on Miter TableMounting Hole Optional AccessoriesElectrical Connection Trace HolesTo Install Blade AssemblyDust Guide Dust BAG Stop Block Table ExtensionsPivot Adjustments Travel Pivot Adjustment AdjustmentsAuthorized Service Center See Figures 17 Squaring the Miter Table to the FenceFence Miter Table FEN CESquaring the SAW Blade to the Fence FENCE, Adjustments are Required FigSee Figures 21 Fence Miter Blade Framinglock Plate SquareApplications OperationCutting with Your Miter SAW CrosscuttingLong Workpiece Workpiece Supports Support Long WorkpiecesClamping Wide Workpieces Cutting Warped MaterialSee Figures 27 RightGeneral MaintenanceLubrication Extension CordsProceed as follows when replacement is required Brush ReplacementBrush CAP Assembly Problem Cause Solution TroubleshootingRyobi TECHNOLOGIES, INC Operators Manual 10 in mm Miter Saw Model TS1301
Top Page Image Contents