Ryobi TS1301 warranty Operation, Applications, Cutting with Your Miter SAW, Crosscutting

Page 18

OPERATION

APPLICATIONS

(Use only for the purposes listed below)

Cross cutting wood and plastic.

Cross cutting miters, joints, etc. for picture frames, moldings, door casings, and fine joinery.

NOTE: The crosscut blade provided is fine for most wood cutting operations, but for fine joinery cuts or cutting plastic, use one of the accessory blades available from your Ryobi dealer.

WARNING:

Before starting any cutting operation, clamp or bolt your miter saw to a workbench. Never operate your miter saw on the floor or in a crouched position. Failure to heed this warning can result in serious personal injury.

CUTTING WITH YOUR MITER SAW

WARNING:

When using a work clamp or C-clamp to secure your workpiece against the fence, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. The workpiece binding the blade will cause motor stalling and kickback. This situation could cause an accident resulting in possible serious personal injury.

CROSSCUTTING

See Figure 25.

A crosscut is made by cutting across the grain of the workpiece. A straight crosscut is made with the miter table set at the zero degree position. Miter crosscuts are made with the miter table set at some angle other than zero.

TO CROSSCUT WITH YOUR MITER SAW:

Pull out the lock pin and lift saw arm to its full height.

Loosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen.

Press the miter lock plate down with your thumb and hold.

Rotate the control arm until the pointer aligns with the desired angle on the miter scale.

Release the miter lock plate.

NOTE: You can quickly locate 0° , or 15° , 22-1/2° , 30° , and 45° left or right by releasing the miter lock plate as you rotate the control arm. The miter lock plate will seat itself in one of the positive stop notches, located in the miter table frame.

Tighten the miter lock handle securely.

8 8 7 7 6 6

5 5 4 4 3 3 2 2

1

STRAIGHT CROSSCUT

Fig. 25

WARNING:

To avoid serious personal injury, always tighten the miter lock handle securely before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut.

Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board is placed against the fence, the board could collapse on the blade at the end of the cut, jamming the blade. See Figures 27 and 28.

When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. See Figure 25.

Align cutting line on the workpiece with the edge of saw blade.

Grasp the stock firmly with one hand and secure it against the fence. Use the work clamp or a C-clamp to secure the workpiece when possible.

WARNING:

To avoid serious personal injury, keep your hands outside the no hands zone and at least 3 in. (76.2 mm) from blade. Never perform any cutting operation freehand (without securing workpiece against the fence). The blade could grab the workpiece if it slips or twists.

Page 18

Image 18
Contents Save this Manual for Future Reference Thank YOU for Buying a Ryobi Miter SAWTable of Contents Symbol Meaning Safety Alert Symbol Rules for Safe OperationDouble Insulation Read ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Additional Rules For Safe Operation For Miter Saws Glossary of Terms for Woodworking Unpacking and Checking Contents Features Trigger Lock Miter Lock HandleSpindle Lock Button Positive Stops on Miter TableElectrical Connection Optional AccessoriesMounting Hole Trace HolesAssembly To Install BladeDust Guide Dust BAG Table Extensions Stop BlockAdjustments Pivot Adjustments Travel Pivot AdjustmentAuthorized Service Center Fence Miter Table Squaring the Miter Table to the FenceSee Figures 17 FEN CESee Figures 21 FENCE, Adjustments are Required FigSquaring the SAW Blade to the Fence Fence Miter Blade Framinglock Plate SquareCutting with Your Miter SAW OperationApplications CrosscuttingSupport Long Workpieces Long Workpiece Workpiece SupportsSee Figures 27 Cutting Warped MaterialClamping Wide Workpieces RightLubrication MaintenanceGeneral Extension CordsBrush Replacement Proceed as follows when replacement is requiredBrush CAP Assembly Troubleshooting Problem Cause SolutionOperators Manual 10 in mm Miter Saw Model TS1301 Ryobi TECHNOLOGIES, INC