Ryobi TS1301 warranty Unpacking and Checking Contents

Page 8

UNPACKING AND CHECKING CONTENTS

Your Miter Saw has been shipped completely assembled except for the blade, miter lock handle, dust guide or dust bag, table extensions, and stop block.

■Remove all loose parts from the carton. Separate and check with the list of Loose Parts. See Figure 1.

■Remove the packing materials from around your saw.

■Carefully lift saw from the carton and place it on a level work surface. Although small, this saw is heavy. To avoid back injury, get help when needed.

■Do not discard the packing materials until you have carefully inspected the saw, identified all loose parts, and satisfactorily operated your new saw.

■Your saw has been shipped with the saw arm locked in the down position. To release saw arm, push down on top of saw arm and pull out the lock pin. See Figure 3.

■Lift the saw arm by the handle. Hand pressure should remain on the saw arm to prevent sudden rise upon release of the lock pin.

■Examine all parts to make sure no breakage or damage has occurred during shipping.

If any parts are damaged or missing, do not attempt to plug in the power cord and turn the switch on until the damaged or missing parts are obtained and are installed correctly. Contact your nearest Ryobi dealer or call 1-800-525-2579 in the United States for assistance if any parts are missing or damaged.

WARNING:

If any parts are missing do not operate your saw until the missing parts are replaced. Failure to do so could result in possible serious injury.

LOOSE PARTS LIST

The following items are included with your Miter Saw:

■10 in. (254 mm) Blade

■Miter Lock Handle

■Dust Bag

■Dust Guide

■Stop Block

■Small Wing Screw (for use with stop block)

■Table Extensions (2)

■Clamp Bracket (2), (for use with table extensions)

■Clamp Bracket Screw (2), (for use with table extensions)

■Blade Wrench (1/4 in. Hey Key/Phillips Screwdriver)

■Operator's Manual

■Warranty Registration

Some models may include one or more of the following accessories:

■Work Clamp

■8 mm Work Clamp Screw

DUST BAG

BLADE WRENCH

SAW BLADE

MITER

LOCK HANDLE

CLAMP

BRACKET SCREWS

CLAMP BRACKETS

SMALL

WING SCREW

STOP BLOCK

DUST GUIDE

TABLE EXTENSIONS

Fig. 1

 

Page 8

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Save this Manual for Future Reference Thank YOU for Buying a Ryobi Miter SAWTable of Contents Double Insulation Symbol Meaning Safety Alert SymbolRules for Safe Operation Read ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Additional Rules For Safe Operation For Miter Saws Glossary of Terms for Woodworking Unpacking and Checking Contents Features Miter Lock Handle Spindle Lock ButtonTrigger Lock Positive Stops on Miter TableOptional Accessories Mounting HoleElectrical Connection Trace HolesDust Guide AssemblyTo Install Blade Dust BAG Table Extensions Stop BlockAuthorized Service Center AdjustmentsPivot Adjustments Travel Pivot Adjustment Squaring the Miter Table to the Fence See Figures 17Fence Miter Table FEN CEFENCE, Adjustments are Required Fig Squaring the SAW Blade to the FenceSee Figures 21 Fence Miter Blade Framinglock Plate SquareOperation ApplicationsCutting with Your Miter SAW CrosscuttingSupport Long Workpieces Long Workpiece Workpiece SupportsCutting Warped Material Clamping Wide WorkpiecesSee Figures 27 RightMaintenance GeneralLubrication Extension CordsBrush CAP Assembly Brush ReplacementProceed as follows when replacement is required Troubleshooting Problem Cause SolutionOperators Manual 10 in mm Miter Saw Model TS1301 Ryobi TECHNOLOGIES, INC
Top Page Image Contents