Ryobi BTS20 manual To Check SAW Blade Installation, To Install Blade Guard Assembly

Page 18

ASSEMBLY

BLADE AND GUARD ASSEMBLY

WARNING:

Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious injury.

TO CHECK SAW BLADE INSTALLATION

￿To check the saw blade, first remove the screw holding the throat plate in place. Remove the throat plate. See Figure 14.

￿Make sure the bevel locking lever is locked. Raise the blade arbor to its full height by turning the blade adjusting handle counterclockwise.

￿Using the smaller hex wrench, insert the flat open end into the flats on the arbor shaft as shown. Insert the larger hex wrench over the hex nut, and, holding both wrenches firmly, pull the larger wrench forward to the front of the machine to loosen and push to tighten. Make sure the blade nut is securely tightened. Do not overtighten.

Note: Arbor shaft has right-hand threads.

￿Check all clearances for free blade rotation.

TO INSTALL BLADE GUARD ASSEMBLY

￿Lower the blade by turning the blade adjustment handle clockwise.

￿Using the small hex wrench, install the blade guard assembly by loosening the two attachment hex nuts enough to slide the riving knife down between the shims. See Figure 16. Partially retighten the two attachment nuts. Check the blade and riving knife alignment. Make sure riving knife clears blade by 1/8 in. See Figure 24.

￿Correctly align the blade and riving knife as shown, repeating above step as needed. Tighten attachment nuts securely. If riving knife is not positioned correctly with blade up, it could contact saw table when blade is lowered and restrict blade elevation.

SMALL HEX

WRENCH

LARGE

HEX WRENCH

Fig. 14

NOTE: PLACE BLADE BETWEEN

INNER AND OUTER BLADE WASHER

SMALL

LARGE HEX HEX WRENCH

WRENCH

SMALL

SPACER

TO

LOOSEN

ARBOR

LARGE

SPACER

INNER

BLADE WASHER

OUTER

BLADE WASHER

 

TO

 

ARBOR NUT

TIGHTEN

Fig. 15

 

RIVING

KNIFE

SHIMS

HEX NUTS

MOUNTING PLATE

DO NOT REMOVE HEX NUTS

Fig. 16

Page 18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents Product SpecificationsSymbol Meaning Rules for Safe OperationRead ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Blades Coast After Turn OFFSafety and International Symbols Electrical Connection ElectricalExtension Cords Grounding InstructionsGlossary of Terms Unpacking Tools NeededWrench #2 Phillips Screwdriver Framing Square Loose Parts List Key Description QtyFeatures Getting to Know Your SAWPower Switch Operating ComponentsSpeed and Wiring BladesPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Assembling Bumpers AssemblyAssembling Wheels and HUB Caps WheelOpening the LEG Stand Closing the LEG Stand RIP Fence Front Rail To Install RIP FenceREMOVING/REPLACING the Throat Plate Finger HoleTo Check SAW Blade Installation To Install Blade Guard AssemblyReplacing the Throat Plate Operation Types of Cuts Blade Throatguard Plate Rotate Blade AdjustingTo Remove the Blade Push Bevel Locking Locking Lever LeftTo CHECK, Replace or Adjust the Blade Guard Assembly Riving Knife Shims HEX NutsInch To Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade Heeling Paralleling the Blade to the Miter Gage Groove See Figures 28To Make a Cross CUT To USE Outfeed SupportTo USE Sliding Table Extension Miter Gauge Extension Scale WindowTo Make a Miter CUT To Make a Straight RIP CUTTo Make a Bevel Cross CUT To Make a Bevel RIP CUTMiter Gauge RIP Fence Bevel Locking Lever Featherboard To Make a Compound Miter CUTTo Make NON-THROUGH Cuts Bevel Locking Lever Pushblock ClampTo Make Dado Cuts MaintenanceGeneral Maintenance LubricationStop Bolt To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Nuts Clamp Screw RIP Fence Blade Locking Handle ScrewsTrouble Shooting Problem Possible Cause SolutionPage Operators Manual 10 in mm Table Saw Model BTS20 Ryobi TECHNOLOGIES, INC

BTS20 specifications

The Ryobi BTS20 is a versatile and efficient table saw that caters to both DIY enthusiasts and professional woodworkers alike. Designed with precision and user-friendliness in mind, the BTS20 is a reliable addition to any workshop, delivering impressive cutting performance and functionality.

One of the standout features of the Ryobi BTS20 is its powerful 15-amp motor, which provides ample power to tackle a variety of cutting tasks. The motor is capable of delivering a no-load speed of up to 5,000 RPM, ensuring that users can make clean and accurate cuts through different materials, including hardwoods and plywood. This makes the BTS20 suitable for a wide range of applications, from small home projects to larger, more complex woodworking endeavors.

The table saw boasts a spacious 27-inch by 18-inch table surface, providing ample workspace for larger workpieces and ensuring stability during operations. The tabletop is made from high-quality materials to enhance durability and promote smooth feeding of materials. Furthermore, the BTS20 features an adjustable fence system, which allows for quick and precise adjustments, ensuring accurate cuts every time.

Safety is a fundamental consideration in the design of the Ryobi BTS20. The saw is equipped with a blade guard that helps protect users from accidental contact with the blade during operation. Additionally, the saw includes an electric brake that stops the blade quickly, minimizing the risk of injury. With built-in kickback protection, the BTS20 also helps to keep the user safe from unforeseen accidents during cutting tasks.

Another noteworthy characteristic of the Ryobi BTS20 is its portability. The saw includes foldable legs that make it easy to set up and take down, allowing users to transport it between job sites with ease. The lightweight design contributes to its portability while ensuring that it remains stable during operation.

In terms of technology, the Ryobi BTS20 features a well-engineered dust collection system that helps maintain a clean workspace. This system is designed to minimize the amount of sawdust and debris produced during cutting, contributing not only to cleanliness but also to better visibility of the work area.

In conclusion, the Ryobi BTS20 is a power-packed table saw that combines performance, safety, and portability. With its robust motor, spacious work surface, and user-friendly features, it stands as an impressive option for anyone serious about woodworking. Whether you're crafting a new piece of furniture or tackling home renovations, the Ryobi BTS20 will not disappoint.
Top Page Image Contents