Ryobi BTS20 Blades Coast After Turn OFF, Before Making a CUT, be Sure ALL Adjustments are Secure

Page 5

RULES FOR SAFE OPERATION

￿BLADES COAST AFTER TURN OFF.

￿NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes.

￿INSPECT TOOL CORDS PERIODICALLY. If damaged, have repaired by a qualified service technician at an authorized service facility. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Repair or replace a damaged or worn cord immediately. Stay constantly aware of cord location and keep it well away from the rotating blade.

￿INSPECT EXTENSION CORDS PERIODICALLY and replace if damaged.

￿KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool.

￿STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.

￿DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

￿GUARD AGAINST KICKBACK. Kickback occurs when the blade stalls rapidly and workpiece is driven back towards the operator. It can pull your hand into the blade resulting in serious personal injury. Stay out of blade path and turn switch off immediately if blade binds or stalls.

￿USE RIP FENCE. Always use a fence or straight edge guide when ripping.

￿SUPPORT LARGE PANELS. To minimize risk of blade pinching and kickback, always support large panels.

￿BEFORE MAKING A CUT, BE SURE ALL ADJUSTMENTS ARE SECURE.

￿USE ONLY CORRECT BLADES. Do not use blades with incorrect size holes. Never use blade washers or bolts that are defective or incorrect. The maximum blade capacity of your saw is 10 in. (254 mm).

￿AVOID CUTTING NAILS. Inspect for and remove all nails from lumber before cutting.

￿NEVER TOUCH BLADE or other moving parts during use.

￿NEVER START A TOOL WHEN ANY ROTATING COMPONENT IS IN CONTACT WITH THE WORKPIECE.

￿DO NOT OPERATE THIS TOOL WHILE UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICATION.

￿GROUND ALL TOOLS. If tool is equipped with three- prong plug, it should be plugged into a three-hole electrical receptacle.

￿WHEN SERVICING use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.

￿REMOVE ALL FENCES AND AUXILIARY TABLES before transporting saw. Failure to do so can result in an accident causing possible serious personal injury.

￿ALWAYS USE BLADE GUARD, RIVING KNIFE, AND ANTI-KICKBACK PAWLS on all "through-sawing" op- erations. Through-sawing operations are those in which the blade cuts completely through the workpiece as in ripping or crosscutting. Keep the blade guard down, the anti-kickback pawls down, and the riving knife in place over the blade.

￿ALWAYS SECURE WORK firmly against rip fence or miter fence.

￿ALWAYS USE A PUSH STICK FOR RIPPING NARROW STOCK. A push stick is a device used to push a workpiece through the blade instead of using your hands. Size and shape can vary but the push stick must always be nar- rower than the workpiece to prevent the push stick from contacting the saw blade. When ripping narrow stock, always use a push stick, so your hand does not come close to the saw blade. Use a featherboard and push blocks for non-through cuts.

￿NEVER perform any operation "freehand" which means using only your hands to support or guide the workpiece. Always use either the rip fence or miter fence to position and guide the work.

￿NEVER stand or have any part of your body in line with the path of the saw blade.

￿NEVER reach behind, over, or within three inches of the blade or cutter with either hand for any reason.

￿MOVE THE RIP FENCE out of the way when crosscutting.

￿NEVER use rip fence as cutoff gage when crosscutting.

￿NEVER attempt to free a stalled saw blade without first turning the saw OFF and disconnecting the saw from the power source.

￿PROVIDE ADEQUATE SUPPORT to the rear and sides of the saw table for wide or long work pieces. Use a sturdy "outrigger" support if a table extension more than 24 inches long is attached to the saw.

￿AVOID KICKBACKS (work thrown back toward you) by:

A.Keeping blade sharp.

B.Keeping rip fence parallel to the saw blade.

C.Keeping riving knife, anti-kickback pawls, and blade guard in place and operating.

D.Not releasing the work before it is pushed all the way past the saw blade using a push stick.

E.Not ripping work that is twisted or warped or does not have a straight edge to guide along the fence.

￿AVOID AWKWARD OPERATIONS AND HAND POSI- TIONS where a sudden slip could cause your hand to move into the cutting tool.

Page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Extension Cords ElectricalElectrical Connection Grounding InstructionsGlossary of Terms Wrench #2 Phillips Screwdriver Framing Square UnpackingTools Needed Key Description Qty Loose Parts ListGetting to Know Your SAW FeaturesOperating Components Power SwitchPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Speed and WiringBlades Assembling Wheels and HUB Caps AssemblyAssembling Bumpers WheelOpening the LEG Stand Closing the LEG Stand REMOVING/REPLACING the Throat Plate To Install RIP FenceRIP Fence Front Rail Finger HoleTo Install Blade Guard Assembly To Check SAW Blade InstallationReplacing the Throat Plate Operation Types of Cuts To Remove the Blade Rotate Blade AdjustingBlade Throatguard Plate Push Bevel Locking Locking Lever LeftInch To CHECK, Replace or Adjust the Blade Guard AssemblyRiving Knife Shims HEX Nuts To SET the Scale to the Blade To Adjust the Blade DepthTo Adjust the Blade Angle See Figures 28 Heeling Paralleling the Blade to the Miter Gage GrooveTo USE Sliding Table Extension To USE Outfeed SupportTo Make a Cross CUT Miter Gauge Extension Scale WindowTo Make a Straight RIP CUT To Make a Miter CUTMiter Gauge RIP Fence Bevel Locking Lever To Make a Bevel Cross CUTTo Make a Bevel RIP CUT To Make NON-THROUGH Cuts To Make a Compound Miter CUTFeatherboard Bevel Locking Lever Pushblock ClampGeneral Maintenance MaintenanceTo Make Dado Cuts LubricationTo Check the Alignment of the RIP Fence to the Blade To SET Blade AT 0 orStop Bolt Nuts Clamp Screw RIP Fence Blade Locking Handle ScrewsProblem Possible Cause Solution Trouble ShootingPage Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BTS20

BTS20 specifications

The Ryobi BTS20 is a versatile and efficient table saw that caters to both DIY enthusiasts and professional woodworkers alike. Designed with precision and user-friendliness in mind, the BTS20 is a reliable addition to any workshop, delivering impressive cutting performance and functionality.

One of the standout features of the Ryobi BTS20 is its powerful 15-amp motor, which provides ample power to tackle a variety of cutting tasks. The motor is capable of delivering a no-load speed of up to 5,000 RPM, ensuring that users can make clean and accurate cuts through different materials, including hardwoods and plywood. This makes the BTS20 suitable for a wide range of applications, from small home projects to larger, more complex woodworking endeavors.

The table saw boasts a spacious 27-inch by 18-inch table surface, providing ample workspace for larger workpieces and ensuring stability during operations. The tabletop is made from high-quality materials to enhance durability and promote smooth feeding of materials. Furthermore, the BTS20 features an adjustable fence system, which allows for quick and precise adjustments, ensuring accurate cuts every time.

Safety is a fundamental consideration in the design of the Ryobi BTS20. The saw is equipped with a blade guard that helps protect users from accidental contact with the blade during operation. Additionally, the saw includes an electric brake that stops the blade quickly, minimizing the risk of injury. With built-in kickback protection, the BTS20 also helps to keep the user safe from unforeseen accidents during cutting tasks.

Another noteworthy characteristic of the Ryobi BTS20 is its portability. The saw includes foldable legs that make it easy to set up and take down, allowing users to transport it between job sites with ease. The lightweight design contributes to its portability while ensuring that it remains stable during operation.

In terms of technology, the Ryobi BTS20 features a well-engineered dust collection system that helps maintain a clean workspace. This system is designed to minimize the amount of sawdust and debris produced during cutting, contributing not only to cleanliness but also to better visibility of the work area.

In conclusion, the Ryobi BTS20 is a power-packed table saw that combines performance, safety, and portability. With its robust motor, spacious work surface, and user-friendly features, it stands as an impressive option for anyone serious about woodworking. Whether you're crafting a new piece of furniture or tackling home renovations, the Ryobi BTS20 will not disappoint.
Top Page Image Contents