Ryobi BTS20 manual To Make a Miter CUT, To Make a Straight RIP CUT

Page 27

OPERATION

￿Set the miter gauge to 0û and tighten the lock knob.

￿Place a support (the same height as saw table) behind the saw for the cut work.

￿Make sure the wood is clear of the blade before turning on the saw.

￿To turn the saw on ( ), lift the switch button.

￿To turn saw off ( ), press the switch button down. Note: To prevent unauthorized use, remove the switch key as shown in figure 34.

￿Let the blade build up to full speed before moving the workpiece into the blade.

￿Hold the workpiece firmly with both hands on the miter gauge and feed the workpiece into the blade.

￿When the cut is made, turn the saw off ( ). Wait for the blade to come to a complete stop before removing the workpiece.

TO MAKE A MITER CUT

See Figure 35.

It is recommended you make test cuts on scrap wood.

WARNING:

Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.

￿Remove the rip fence by lifting the locking handle.

￿Set the miter gauge to the desired angle and tighten the lock knob.

￿Place a support (the same height as saw table) behind the saw for the cut work.

￿Make sure the wood is clear of the blade before turning on the saw.

￿Let the blade build up to full speed before moving the workpiece into the blade.

￿Feed the workpiece into the blade until the cut has been completed.

TO MAKE A STRAIGHT RIP CUT

See Figure 36.

It is recommended you make a test cut on scrap wood.

WARNING:

Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.

￿Position the rip fence the desired distance from the blade for the cut and securely lock the handle. Adjust the scale to zero at the cutting edge of the blade.

￿Place a support (the same height as saw table) behind the saw for the cut work.

￿Make sure the wood is clear of the blade before turning on the saw.

￿Use a push block or push stick to move the wood through the cut past the blade. Never push a small piece of wood into the blade with your hand, always use a push stick. The use of push blocks, push sticks, and featherboards are necessary when making non-through cuts.

￿Stand to the side of the wood as it contacts the blade to reduce the chance of injury should kickback occur. Never stand directly in the line of cut.

￿Make sure the wood is clear of the blade before turning on the saw.

￿Let the blade build up to full speed before feeding the workpiece into the blade.

￿When the cut is made, turn the saw off ( ). Wait for the blade to come to a complete stop before removing the workpiece.

SWITCH

KEY

SWITCH IN LOCKED POSITION

Fig. 34

MITER GAUGE

BLADE

GUARD ASSEMBLY

-

+

 

 

 

Fig. 35

OUTFEED SUPPORT

RIP FENCE

BLADE

 

PUSHSTICK

-

+

FRONT

RAIL

LOCKING HANDLE

Fig. 36

Page 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Grounding Instructions ElectricalExtension Cords Electrical ConnectionGlossary of Terms Unpacking Tools NeededWrench #2 Phillips Screwdriver Framing Square Key Description Qty Loose Parts ListGetting to Know Your SAW FeaturesOperating Components Power SwitchSpeed and Wiring BladesPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Wheel AssemblyAssembling Wheels and HUB Caps Assembling BumpersOpening the LEG Stand Closing the LEG Stand Finger Hole To Install RIP FenceREMOVING/REPLACING the Throat Plate RIP Fence Front RailTo Install Blade Guard Assembly To Check SAW Blade InstallationReplacing the Throat Plate Operation Types of Cuts Push Bevel Locking Locking Lever Left Rotate Blade AdjustingTo Remove the Blade Blade Throatguard PlateTo CHECK, Replace or Adjust the Blade Guard Assembly Riving Knife Shims HEX NutsInch To Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade See Figures 28 Heeling Paralleling the Blade to the Miter Gage GrooveMiter Gauge Extension Scale Window To USE Outfeed SupportTo USE Sliding Table Extension To Make a Cross CUTTo Make a Straight RIP CUT To Make a Miter CUTTo Make a Bevel Cross CUT To Make a Bevel RIP CUTMiter Gauge RIP Fence Bevel Locking Lever Bevel Locking Lever Pushblock Clamp To Make a Compound Miter CUTTo Make NON-THROUGH Cuts FeatherboardLubrication MaintenanceGeneral Maintenance To Make Dado CutsNuts Clamp Screw RIP Fence Blade Locking Handle Screws To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Stop BoltProblem Possible Cause Solution Trouble ShootingPage Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BTS20

BTS20 specifications

The Ryobi BTS20 is a versatile and efficient table saw that caters to both DIY enthusiasts and professional woodworkers alike. Designed with precision and user-friendliness in mind, the BTS20 is a reliable addition to any workshop, delivering impressive cutting performance and functionality.

One of the standout features of the Ryobi BTS20 is its powerful 15-amp motor, which provides ample power to tackle a variety of cutting tasks. The motor is capable of delivering a no-load speed of up to 5,000 RPM, ensuring that users can make clean and accurate cuts through different materials, including hardwoods and plywood. This makes the BTS20 suitable for a wide range of applications, from small home projects to larger, more complex woodworking endeavors.

The table saw boasts a spacious 27-inch by 18-inch table surface, providing ample workspace for larger workpieces and ensuring stability during operations. The tabletop is made from high-quality materials to enhance durability and promote smooth feeding of materials. Furthermore, the BTS20 features an adjustable fence system, which allows for quick and precise adjustments, ensuring accurate cuts every time.

Safety is a fundamental consideration in the design of the Ryobi BTS20. The saw is equipped with a blade guard that helps protect users from accidental contact with the blade during operation. Additionally, the saw includes an electric brake that stops the blade quickly, minimizing the risk of injury. With built-in kickback protection, the BTS20 also helps to keep the user safe from unforeseen accidents during cutting tasks.

Another noteworthy characteristic of the Ryobi BTS20 is its portability. The saw includes foldable legs that make it easy to set up and take down, allowing users to transport it between job sites with ease. The lightweight design contributes to its portability while ensuring that it remains stable during operation.

In terms of technology, the Ryobi BTS20 features a well-engineered dust collection system that helps maintain a clean workspace. This system is designed to minimize the amount of sawdust and debris produced during cutting, contributing not only to cleanliness but also to better visibility of the work area.

In conclusion, the Ryobi BTS20 is a power-packed table saw that combines performance, safety, and portability. With its robust motor, spacious work surface, and user-friendly features, it stands as an impressive option for anyone serious about woodworking. Whether you're crafting a new piece of furniture or tackling home renovations, the Ryobi BTS20 will not disappoint.
Top Page Image Contents