Ryobi BTS20 manual Heeling Paralleling the Blade to the Miter Gage Groove, See Figures 28

Page 25

OPERATION

HEELING (PARALLELING) THE BLADE TO THE MITER GAGE GROOVE

See Figures 28 - 30 .

WARNING:

Make sure the switch is off, switch key is removed, and saw is unplugged. Failure to do so could result in accidental starting causing serious personal injury.

Do not loosen any screws for this adjustment until you have checked with a square and made test cuts to be sure adjusments are necessary. Once the screws are loosened, these items must be reset.

WARNING:

The blade must parallel the miter gage slot so the wood does not bind resulting in kickback. Failure to do so could result in serious personal injury.

￿Lift the blade guard. Raise the blade all the way by turning the height handwheel.

￿Mark beside one of the blade teeth at the front of the blade. Place the body of a combination square against the miter gage groove as shown in figure 28. Measure the distance to the right gage groove.

￿Turn the blade so the marked tooth is at the back.

￿Move the combination square to the rear and again measure the distance to the right miter gage groove. If the distances are the same, the blade and the miter gage groove are parallel.

￿If the distances measured are different, loosen the screws at the back of the table using a 4 mm hex key.

￿If the back of the blade was too far from the miter gage groove, place a block of wood on the left side of the blade and push it into the blade until the blade is parallel to the miter gage groove. Retighten the screws.

￿If the back of the blade was too close to the miter gage groove, place a block of wood on the right side of the blade and push it into the blade until the blade is parallel to the miter gage groove. Retighten the screws.

WARNING:

To reduce the risk of injury from kickback, align the rip fence to the blade following any blade adjustments. Always make sure the rip fence is parallel to the blade before beginning any operation.

SCREWS

RIGHT MITER

GAGE GROOVE

COMBINATION

SQUARE

Fig. 28

COMBINATION

SQUARE

Fig. 29

BLADE TOO CLOSE TO MITER GAGE GROOVE

Fig. 30

Page 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Extension Cords ElectricalElectrical Connection Grounding InstructionsGlossary of Terms Tools Needed UnpackingWrench #2 Phillips Screwdriver Framing Square Key Description Qty Loose Parts ListGetting to Know Your SAW FeaturesOperating Components Power SwitchBlades Speed and WiringPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Assembling Wheels and HUB Caps AssemblyAssembling Bumpers WheelOpening the LEG Stand Closing the LEG Stand REMOVING/REPLACING the Throat Plate To Install RIP FenceRIP Fence Front Rail Finger HoleTo Install Blade Guard Assembly To Check SAW Blade InstallationReplacing the Throat Plate Operation Types of Cuts To Remove the Blade Rotate Blade AdjustingBlade Throatguard Plate Push Bevel Locking Locking Lever LeftRiving Knife Shims HEX Nuts To CHECK, Replace or Adjust the Blade Guard AssemblyInch To Adjust the Blade Angle To Adjust the Blade DepthTo SET the Scale to the Blade See Figures 28 Heeling Paralleling the Blade to the Miter Gage GrooveTo USE Sliding Table Extension To USE Outfeed SupportTo Make a Cross CUT Miter Gauge Extension Scale WindowTo Make a Straight RIP CUT To Make a Miter CUTTo Make a Bevel RIP CUT To Make a Bevel Cross CUTMiter Gauge RIP Fence Bevel Locking Lever To Make NON-THROUGH Cuts To Make a Compound Miter CUTFeatherboard Bevel Locking Lever Pushblock ClampGeneral Maintenance MaintenanceTo Make Dado Cuts LubricationTo Check the Alignment of the RIP Fence to the Blade To SET Blade AT 0 orStop Bolt Nuts Clamp Screw RIP Fence Blade Locking Handle ScrewsProblem Possible Cause Solution Trouble ShootingPage Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BTS20

BTS20 specifications

The Ryobi BTS20 is a versatile and efficient table saw that caters to both DIY enthusiasts and professional woodworkers alike. Designed with precision and user-friendliness in mind, the BTS20 is a reliable addition to any workshop, delivering impressive cutting performance and functionality.

One of the standout features of the Ryobi BTS20 is its powerful 15-amp motor, which provides ample power to tackle a variety of cutting tasks. The motor is capable of delivering a no-load speed of up to 5,000 RPM, ensuring that users can make clean and accurate cuts through different materials, including hardwoods and plywood. This makes the BTS20 suitable for a wide range of applications, from small home projects to larger, more complex woodworking endeavors.

The table saw boasts a spacious 27-inch by 18-inch table surface, providing ample workspace for larger workpieces and ensuring stability during operations. The tabletop is made from high-quality materials to enhance durability and promote smooth feeding of materials. Furthermore, the BTS20 features an adjustable fence system, which allows for quick and precise adjustments, ensuring accurate cuts every time.

Safety is a fundamental consideration in the design of the Ryobi BTS20. The saw is equipped with a blade guard that helps protect users from accidental contact with the blade during operation. Additionally, the saw includes an electric brake that stops the blade quickly, minimizing the risk of injury. With built-in kickback protection, the BTS20 also helps to keep the user safe from unforeseen accidents during cutting tasks.

Another noteworthy characteristic of the Ryobi BTS20 is its portability. The saw includes foldable legs that make it easy to set up and take down, allowing users to transport it between job sites with ease. The lightweight design contributes to its portability while ensuring that it remains stable during operation.

In terms of technology, the Ryobi BTS20 features a well-engineered dust collection system that helps maintain a clean workspace. This system is designed to minimize the amount of sawdust and debris produced during cutting, contributing not only to cleanliness but also to better visibility of the work area.

In conclusion, the Ryobi BTS20 is a power-packed table saw that combines performance, safety, and portability. With its robust motor, spacious work surface, and user-friendly features, it stands as an impressive option for anyone serious about woodworking. Whether you're crafting a new piece of furniture or tackling home renovations, the Ryobi BTS20 will not disappoint.
Top Page Image Contents