Ryobi BTS20 manual To Make a Bevel Cross CUT, To Make a Bevel RIP CUT

Page 28

OPERATION

TO MAKE A BEVEL CROSS CUT

See Figure 37.

It is recommended that you place the piece to be saved on the left side of the blade and that you make a test cut on scrap wood.

WARNING:

Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.

￿Unlock the bevel locking lever.

￿Remove the rip fence by lifting the locking handle.

￿Turn the bevel handle until the bevel indicator is at the desired angle. Push the bevel locking lever securely to the left to lock the angle.

￿Set the blade to the correct depth for the workpiece.

￿Set the miter gauge to 90° and press the bevel locking lever towards the table to lock.

￿Place a support (the same height as saw table) behind the saw for the cut work.

￿Make sure the wood is clear of the blade before turning on the saw.

￿Let the saw blade build up to full speed before moving the miter gauge and the workpiece into the blade.

￿Hold the workpiece firmly with both hands on the miter gauge and feed the workpiece into the blade.

￿When the cut is made, turn the saw off ( ). Wait for the blade to come to a complete stop before removing the workpiece.

TO MAKE A BEVEL RIP CUT

See Figure 38.

It is recommended you make test cuts on scrap wood.

WARNING:

The rip fence must be on the right side of the blade to avoid trapping the wood and causing kickback.

WARNING:

Make sure the blade guard assembly is installed and working properly to reduce the risk of serious personal injury.

￿Remove the miter gauge.

￿Position the rip fence the desired distance from the right side of the blade and lock down the handle.

￿Adjust the bevel angle to the desired setting.

￿Set the blade to the correct depth.

￿If ripping a piece larger than 36 in. long, place a support the same height as the table surface behind the saw for the cut work.

MITER GAUGE

-

+

Fig. 37

RIP FENCE

-

+

BEVEL LOCKING LEVER

Fig 38

￿ Turn the power switch to the on ( ) position.

￿Position the workpiece flat on the table with the edge flush against the rip fence. Let the blade build up to full speed before feeding the workpiece into the blade.

￿Using a push stick and/or push blocks, slowly feed the workpiece toward the blade. Stand slightly to the side of the wood as it contacts the blade to reduce the chance of injury should kickback occur.

￿Once the blade has made contact with the workpiece, use the hand closest to the rip fence to guide it. Make sure the edge of the workpiece remains in solid contact with both the rip fence and the surface of the table. If ripping a narrow piece, use a push stick to move the piece through the cut and past the blade.

￿ When the cut is made, turn the saw off ( ). Wait for the blade to come to a complete stop before removing the workpiece.

￿After the blade has stopped completely, remove the cutoff stock.

￿Grasp the workpiece from the lead end (the end fed into the blade first) and carefully remove it from the table.

Page 28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents Product SpecificationsSymbol Meaning Rules for Safe OperationRead ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Blades Coast After Turn OFFSafety and International Symbols Electrical Extension CordsElectrical Connection Grounding InstructionsGlossary of Terms Tools Needed UnpackingWrench #2 Phillips Screwdriver Framing Square Loose Parts List Key Description QtyFeatures Getting to Know Your SAWPower Switch Operating ComponentsBlades Speed and WiringPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Assembly Assembling Wheels and HUB CapsAssembling Bumpers WheelOpening the LEG Stand Closing the LEG Stand To Install RIP Fence REMOVING/REPLACING the Throat PlateRIP Fence Front Rail Finger HoleTo Check SAW Blade Installation To Install Blade Guard AssemblyReplacing the Throat Plate Operation Types of Cuts Rotate Blade Adjusting To Remove the BladeBlade Throatguard Plate Push Bevel Locking Locking Lever LeftRiving Knife Shims HEX Nuts To CHECK, Replace or Adjust the Blade Guard AssemblyInch To Adjust the Blade Angle To Adjust the Blade DepthTo SET the Scale to the Blade Heeling Paralleling the Blade to the Miter Gage Groove See Figures 28To USE Outfeed Support To USE Sliding Table ExtensionTo Make a Cross CUT Miter Gauge Extension Scale WindowTo Make a Miter CUT To Make a Straight RIP CUTTo Make a Bevel RIP CUT To Make a Bevel Cross CUTMiter Gauge RIP Fence Bevel Locking Lever To Make a Compound Miter CUT To Make NON-THROUGH CutsFeatherboard Bevel Locking Lever Pushblock ClampMaintenance General MaintenanceTo Make Dado Cuts LubricationTo SET Blade AT 0 or To Check the Alignment of the RIP Fence to the BladeStop Bolt Nuts Clamp Screw RIP Fence Blade Locking Handle ScrewsTrouble Shooting Problem Possible Cause SolutionPage Operators Manual 10 in mm Table Saw Model BTS20 Ryobi TECHNOLOGIES, INC

BTS20 specifications

The Ryobi BTS20 is a versatile and efficient table saw that caters to both DIY enthusiasts and professional woodworkers alike. Designed with precision and user-friendliness in mind, the BTS20 is a reliable addition to any workshop, delivering impressive cutting performance and functionality.

One of the standout features of the Ryobi BTS20 is its powerful 15-amp motor, which provides ample power to tackle a variety of cutting tasks. The motor is capable of delivering a no-load speed of up to 5,000 RPM, ensuring that users can make clean and accurate cuts through different materials, including hardwoods and plywood. This makes the BTS20 suitable for a wide range of applications, from small home projects to larger, more complex woodworking endeavors.

The table saw boasts a spacious 27-inch by 18-inch table surface, providing ample workspace for larger workpieces and ensuring stability during operations. The tabletop is made from high-quality materials to enhance durability and promote smooth feeding of materials. Furthermore, the BTS20 features an adjustable fence system, which allows for quick and precise adjustments, ensuring accurate cuts every time.

Safety is a fundamental consideration in the design of the Ryobi BTS20. The saw is equipped with a blade guard that helps protect users from accidental contact with the blade during operation. Additionally, the saw includes an electric brake that stops the blade quickly, minimizing the risk of injury. With built-in kickback protection, the BTS20 also helps to keep the user safe from unforeseen accidents during cutting tasks.

Another noteworthy characteristic of the Ryobi BTS20 is its portability. The saw includes foldable legs that make it easy to set up and take down, allowing users to transport it between job sites with ease. The lightweight design contributes to its portability while ensuring that it remains stable during operation.

In terms of technology, the Ryobi BTS20 features a well-engineered dust collection system that helps maintain a clean workspace. This system is designed to minimize the amount of sawdust and debris produced during cutting, contributing not only to cleanliness but also to better visibility of the work area.

In conclusion, the Ryobi BTS20 is a power-packed table saw that combines performance, safety, and portability. With its robust motor, spacious work surface, and user-friendly features, it stands as an impressive option for anyone serious about woodworking. Whether you're crafting a new piece of furniture or tackling home renovations, the Ryobi BTS20 will not disappoint.
Top Page Image Contents