Ryobi BTS20 manual Types of Cuts

Page 21

OPERATION

￿The kerf (the cut made by the blade in the wood) will be wider than the blade to avoid overheating or binding. Make allowance for the kerf when measuring wood.

￿Make sure the kerf is made on the waste side of the measuring line.

￿Cut the wood with the finish side up.

￿Knock out any loose knots with a hammer before making the cut.

￿Always provide proper support for the wood as it comes out of the saw.

TYPES OF CUTS

See Figure 1/.

There are six basic cuts: 1) the cross cut, 2) the rip cut, 3) the miter cut, 4) the bevel cross cut, 5) the bevel rip cut, and 6) the compound (bevel) miter cut. All other cuts are combina- tions of these basic six. Operating procedures for making each kind of cut are given later in this section.

WARNING:

Always make sure the blade guard and anti-kickback pawls are in place and working properly when making these cuts to avoid possible injury.

Cross cuts are straight 90° cuts made across the grain of the workpiece. The wood is fed into the cut at a 90° angle to the blade, and the blade is vertical.

Rip cuts are made with the grain of the wood. To avoid kickback while making a rip cut, make sure one side of the wood rides firmly against the rip fence.

Miter cuts are made with the wood at any angle to the blade other than 90°. The blade is vertical.

WARNING:

Always use a pushstick with small pieces of wood, and also to finish the cut when ripping a long narrow piece of wood, to prevent your hands from getting close to the blade.

Bevel cuts are made with an angled blade. Bevel cross cuts are across the wood grain, and bevel rip cuts are with the grain. The rip fence must always be on the right side of the blade for bevel rip cuts.

Compound (or bevel) miter cuts are made with an angled blade on wood that is angled to the blade. Be thoroughly familiar with making cross cuts, rip cuts, bevel cuts, and miter cuts before trying a compound miter cut.

1

Cross Cut

2

Rip Cut

3

Miter Cut

4

Bevel Cross Cut

5

Bevel Rip Cut

6

Compound (Bevel) Miter Cut

Fig. 19

WARNING:

All blades must be rated for at least 5,500 rpm to prevent possible injury.

Page 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Extension Cords ElectricalElectrical Connection Grounding InstructionsGlossary of Terms Unpacking Tools NeededWrench #2 Phillips Screwdriver Framing Square Key Description Qty Loose Parts ListGetting to Know Your SAW FeaturesOperating Components Power SwitchSpeed and Wiring BladesPrecision Ground MICRO-GRAIN Carbide Teeth Blade Rotation Assembling Wheels and HUB Caps AssemblyAssembling Bumpers WheelOpening the LEG Stand Closing the LEG Stand REMOVING/REPLACING the Throat Plate To Install RIP FenceRIP Fence Front Rail Finger HoleTo Install Blade Guard Assembly To Check SAW Blade InstallationReplacing the Throat Plate Operation Types of Cuts To Remove the Blade Rotate Blade AdjustingBlade Throatguard Plate Push Bevel Locking Locking Lever LeftTo CHECK, Replace or Adjust the Blade Guard Assembly Riving Knife Shims HEX NutsInch To Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade See Figures 28 Heeling Paralleling the Blade to the Miter Gage GrooveTo USE Sliding Table Extension To USE Outfeed SupportTo Make a Cross CUT Miter Gauge Extension Scale WindowTo Make a Straight RIP CUT To Make a Miter CUTTo Make a Bevel Cross CUT To Make a Bevel RIP CUTMiter Gauge RIP Fence Bevel Locking Lever To Make NON-THROUGH Cuts To Make a Compound Miter CUTFeatherboard Bevel Locking Lever Pushblock ClampGeneral Maintenance MaintenanceTo Make Dado Cuts LubricationTo Check the Alignment of the RIP Fence to the Blade To SET Blade AT 0 orStop Bolt Nuts Clamp Screw RIP Fence Blade Locking Handle ScrewsProblem Possible Cause Solution Trouble ShootingPage Ryobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BTS20

BTS20 specifications

The Ryobi BTS20 is a versatile and efficient table saw that caters to both DIY enthusiasts and professional woodworkers alike. Designed with precision and user-friendliness in mind, the BTS20 is a reliable addition to any workshop, delivering impressive cutting performance and functionality.

One of the standout features of the Ryobi BTS20 is its powerful 15-amp motor, which provides ample power to tackle a variety of cutting tasks. The motor is capable of delivering a no-load speed of up to 5,000 RPM, ensuring that users can make clean and accurate cuts through different materials, including hardwoods and plywood. This makes the BTS20 suitable for a wide range of applications, from small home projects to larger, more complex woodworking endeavors.

The table saw boasts a spacious 27-inch by 18-inch table surface, providing ample workspace for larger workpieces and ensuring stability during operations. The tabletop is made from high-quality materials to enhance durability and promote smooth feeding of materials. Furthermore, the BTS20 features an adjustable fence system, which allows for quick and precise adjustments, ensuring accurate cuts every time.

Safety is a fundamental consideration in the design of the Ryobi BTS20. The saw is equipped with a blade guard that helps protect users from accidental contact with the blade during operation. Additionally, the saw includes an electric brake that stops the blade quickly, minimizing the risk of injury. With built-in kickback protection, the BTS20 also helps to keep the user safe from unforeseen accidents during cutting tasks.

Another noteworthy characteristic of the Ryobi BTS20 is its portability. The saw includes foldable legs that make it easy to set up and take down, allowing users to transport it between job sites with ease. The lightweight design contributes to its portability while ensuring that it remains stable during operation.

In terms of technology, the Ryobi BTS20 features a well-engineered dust collection system that helps maintain a clean workspace. This system is designed to minimize the amount of sawdust and debris produced during cutting, contributing not only to cleanliness but also to better visibility of the work area.

In conclusion, the Ryobi BTS20 is a power-packed table saw that combines performance, safety, and portability. With its robust motor, spacious work surface, and user-friendly features, it stands as an impressive option for anyone serious about woodworking. Whether you're crafting a new piece of furniture or tackling home renovations, the Ryobi BTS20 will not disappoint.
Top Page Image Contents