Ryobi BTS10 Assembly, Unpacking, Mounting Holes, To Install the Blade Adjusting Handle, Lock NUT

Page 15

ASSEMBLY

UNPACKING

This product requires assembly.

nCarefully remove the tool and any accessories from the box. Place it on a level work surface.

nInspect the tool carefully to make sure no breakage or damage occurred during shipping.

nDo not discard the packing material until you have carefully inspected the tool, identified all loose parts, and satisfactorily operated the tool.

nIf any parts are damaged or missing, please call 1-800- 525-2579 for assistance.

WARNING:

If any parts are missing do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury.

WARNING:

Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such altera- tion or modification is misuse and could result in a hazard- ous condition leading to possible serious personal injury.

WARNING:

Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.

WARNING:

Never stand directly in line with the blade or allow hands to come closer than 3 in. to the blade. Do not reach over or across the blade. Failure to heed this warning can result in serious personal injury.

WARNING:

To avoid serious personal injury, always make sure the table saw is securely mounted to a workbench or an approved leg stand. NEVER operate the saw on the floor.

MOUNTING HOLES

The table saw must be mounted to a firm supporting surface suchasaworkbenchorlegstand(notincluded).Fourboltholes have been provided in the saw’s base for this purpose. Each of the four mounting holes should be bolted securely using 3/8 in. machine bolts, lock washers, and hex nuts (not included). Bolts should be of sufficient length to accommo- date the saw base, lock washers, hex nuts, and the thickness of the workbench. Tighten all four bolts securely.

Carefully check the workbench after mounting to make sure that no movement can occur during use. If any tipping, slid- ing, or walking is noted, secure the workbench to the floor before operating.

TO INSTALL THE BLADE ADJUSTING HANDLE

See Figure 6.

The blade adjusting handle mounts to the height adjusting handwheel with a shoulder bolt, washer, and lock nut.

nInsert the shoulder bolt in the center of the blade adjusting handle. Place the washer over the bolt and insert into the hole in the height adjusting handwheel.

nPlace the lock nut behind the height adjusting handwheel, and thread the lock nut onto the shoulder bolt.

nHolding the nut in place, tighten with a screwdriver.

LOCK NUT

WASHER

 

SHOULDER

 

BOLT

 

BLADE

HEIGHT

ADJUSTING

HANDLE

ADJUSTING

 

HANDWHEEL

Fig. 6

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules To move into the cutting tool Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Connection Speed and WiringElectrical Extension CordsGlossary of Terms Product Specifications FeaturesOverview Know Your Table SAWPower Switch Overload Reset ButtonBlades Phillips Screwdriver Flathead Framing Square Tools NeededWrench 10 mm, 11 mmKey Description Qty Loose Parts ListMounting Holes AssemblyTo Install the Blade Adjusting Handle UnpackingTo REMOVE/REPLACE the Throat Plate To Check SAW Blade InstallationTo Check and Align the SAW Blade and Blade Guard Assembly To Install Blade Guard AssemblyOperation Types of Cuts Cutting TipsCross CUT Featherboard Push Stick Push Block HOW to Mount a FeatherboardHOW to Make a Featherboard FeatherboardScrewdriver Bevel Indicator To Adjust the Blade DepthTo Adjust the Bevel Angle To Adjust the Bevel IndicatorTo Install the RIP Fence To SET the RIP Fence Scale Indicator to the BladeTo USE the Miter Gauge To Make a Cross CUT Cross CUT Switch OFF Reset ButtonTo Make a Miter CUT To Make a RIP CUTMiter CUT RIP CUT To Make a Bevel Cross CUT To Make a Bevel RIP CUTBevel Cross CUT Bevel RIP CUT Compound Miter CUT To Make a Compound Bevel Miter CUTNON-THROUGH CUT Blade Guard Removed Push Stick To Make a NON-THROUGH CUTAdjustments To Check the Alignment of the RIP Fence to the BladeClamp Screw RIP Fence SAW Blade Screws Locking Handle Positive Stop Adjustment Screw To SET the 90 Positive StopTo SET the 45 Positive Stop To Remove or Change the Blade MaintenanceGeneral Maintenance LubricationProblem Possible Cause Solution TroubleshootingService Model NO. and Serial no

BTS10 specifications

The Ryobi BTS10 is a high-performance table saw designed for both amateur woodworkers and seasoned professionals. Known for its powerful motor and solid construction, this table saw offers a blend of precision and convenience, making it an excellent choice for various woodworking tasks.

One of the standout features of the BTS10 is its robust 15-amp motor, providing ample power to handle tough cutting jobs. This motor ensures that it can effectively rip through hardwoods and softwoods alike, delivering clean and accurate cuts. The tool has a no-load speed of 5000 RPM, allowing for quick and efficient cutting, which is particularly beneficial for large-scale projects.

The BTS10 comes equipped with a spacious 27-inch aluminum table that provides ample workspace, enhancing stability and control during cuts. The table’s surface is designed to be smooth, which minimizes friction and improves accuracy. Moreover, the saw features a cast iron trunnion system that enhances stability, further contributing to the precision of cuts.

For added convenience, the Ryobi BTS10 includes a built-in blade guard and anti-kickback pawls. These safety features are essential in preventing accidents and ensuring user safety during operation. Additionally, this model also incorporates an adjustable miter gauge, allowing users to make angled cuts easily. The miter gauge slides along the table’s slots for increased accuracy when making crosscuts.

The BTS10 also supports a bevel adjustment feature that allows users to tilt the blade up to 45 degrees. This capability is ideal for making bevel cuts, providing versatility for various woodworking applications. The blade height can also be adjusted easily using a convenient handwheel, enhancing user control over cut depth.

In terms of portability, the BTS10 is designed with user convenience in mind. Although it’s built for durability, it remains relatively lightweight, making it easier to transport to job sites or storage.

Overall, the Ryobi BTS10 table saw combines power, usability, and safety features, making it a versatile tool capable of handling a range of woodworking tasks. Whether you’re a hobbyist looking to expand your workshop or a professional seeking a reliable table saw, the BTS10 delivers the performance and features required for precision woodworking.
Top Page Image Contents