Ryobi BTS10 manual General Maintenance, Lubrication, To Remove or Change the Blade, Arbor NUT

Page 30

MAINTENANCE

WARNING:

When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.

WARNING:

Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken, or destroy plastic which may result in serious personal injury.

nPeriodically check all clamps, nuts, bolts, and screws for tightness and condition. Make sure the throat plate is in good condition and in position.

nCheck the blade guard assembly.

nTo maintain the table surfaces, fence, and rails, periodi- cally apply paste wax to them and buff to provide smooth functioning.

nProtect the blade by cleaning out sawdust from underneath the table and in the blade teeth. Use a resin solvent on the blade teeth.

nClean plastic parts only with a soft damp cloth. DO NOT use any aerosol or petroleum solvents.

LUBRICATION

All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrica- tion is required.

TO REMOVE OR CHANGE THE BLADE

See Figure 33.

nRaise the blade to the maximum height.

nRemove the screws and rubber spacers holding the throat plate in place then remove the throat plate.

nTo keep blade arbor from rotating, place the open ended wrench on flats located on the left side of the blade.

nPlace the second wrench over the arbor nut located on the right side of the blade. Turn nut counterclockwise to loosen.

nRemove arbor nut and outer blade washer.

nFirst, lower the saw blade then remove the blade.

nPosition new blade on the arbor, making sure the teeth are pointing down toward the front of the table.

nRaise the saw blade.

nAttach outer blade washer and arbor nut.

nTighten arbor nut, making sure to hold the blade stationary with the open ended wrench.

nReplace throat plate, making sure that the side with the rolled edge underneath is closest to the blade.

nSecurely attach throat plate with screws.

ARBOR NUT

Fig. 33

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules To move into the cutting tool Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningExtension Cords Speed and WiringElectrical Electrical ConnectionGlossary of Terms Features Product SpecificationsKnow Your Table SAW OverviewPower Switch Overload Reset ButtonBlades 10 mm, 11 mm Tools NeededWrench Phillips Screwdriver Flathead Framing SquareLoose Parts List Key Description QtyUnpacking AssemblyTo Install the Blade Adjusting Handle Mounting HolesTo Check SAW Blade Installation To REMOVE/REPLACE the Throat PlateTo Install Blade Guard Assembly To Check and Align the SAW Blade and Blade Guard AssemblyOperation Types of Cuts Cutting TipsCross CUT Featherboard HOW to Mount a FeatherboardHOW to Make a Featherboard Featherboard Push Stick Push BlockTo Adjust the Bevel Indicator To Adjust the Blade DepthTo Adjust the Bevel Angle Screwdriver Bevel IndicatorTo Install the RIP Fence To SET the RIP Fence Scale Indicator to the BladeTo USE the Miter Gauge Cross CUT Switch OFF Reset Button To Make a Cross CUTTo Make a Miter CUT To Make a RIP CUTMiter CUT RIP CUT To Make a Bevel Cross CUT To Make a Bevel RIP CUTBevel Cross CUT Bevel RIP CUT To Make a Compound Bevel Miter CUT Compound Miter CUTTo Make a NON-THROUGH CUT NON-THROUGH CUT Blade Guard Removed Push StickAdjustments To Check the Alignment of the RIP Fence to the BladeClamp Screw RIP Fence SAW Blade Screws Locking Handle Positive Stop Adjustment Screw To SET the 90 Positive StopTo SET the 45 Positive Stop Lubrication MaintenanceGeneral Maintenance To Remove or Change the BladeTroubleshooting Problem Possible Cause SolutionService Model NO. and Serial no

BTS10 specifications

The Ryobi BTS10 is a high-performance table saw designed for both amateur woodworkers and seasoned professionals. Known for its powerful motor and solid construction, this table saw offers a blend of precision and convenience, making it an excellent choice for various woodworking tasks.

One of the standout features of the BTS10 is its robust 15-amp motor, providing ample power to handle tough cutting jobs. This motor ensures that it can effectively rip through hardwoods and softwoods alike, delivering clean and accurate cuts. The tool has a no-load speed of 5000 RPM, allowing for quick and efficient cutting, which is particularly beneficial for large-scale projects.

The BTS10 comes equipped with a spacious 27-inch aluminum table that provides ample workspace, enhancing stability and control during cuts. The table’s surface is designed to be smooth, which minimizes friction and improves accuracy. Moreover, the saw features a cast iron trunnion system that enhances stability, further contributing to the precision of cuts.

For added convenience, the Ryobi BTS10 includes a built-in blade guard and anti-kickback pawls. These safety features are essential in preventing accidents and ensuring user safety during operation. Additionally, this model also incorporates an adjustable miter gauge, allowing users to make angled cuts easily. The miter gauge slides along the table’s slots for increased accuracy when making crosscuts.

The BTS10 also supports a bevel adjustment feature that allows users to tilt the blade up to 45 degrees. This capability is ideal for making bevel cuts, providing versatility for various woodworking applications. The blade height can also be adjusted easily using a convenient handwheel, enhancing user control over cut depth.

In terms of portability, the BTS10 is designed with user convenience in mind. Although it’s built for durability, it remains relatively lightweight, making it easier to transport to job sites or storage.

Overall, the Ryobi BTS10 table saw combines power, usability, and safety features, making it a versatile tool capable of handling a range of woodworking tasks. Whether you’re a hobbyist looking to expand your workshop or a professional seeking a reliable table saw, the BTS10 delivers the performance and features required for precision woodworking.
Top Page Image Contents