Ryobi BTS10 Extension Cords, Electrical Connection, Speed and Wiring, Grounding Instructions

Page 8

ELECTRICAL

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong ground- ing plugs and 3-pole receptacles that accept the tool’s plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat. Use the chart provided below to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter’s Laboratories (UL) should be used.

**Ampere rating (on tool data plate)

 

0-2.0

2.1-3.4

3.5-5.0 5.1-7.0

7.1-12.0

12.1-16.0

 

 

 

 

Cord Length

Wire Size (A.W.G.)

 

 

 

 

 

 

 

 

 

25'

16

16

16

16

14

14

50'

16

16

16

14

14

12

 

 

 

 

 

 

 

100'

16

16

14

12

10

—

**Used on 12 gauge - 20 amp circuit. NOTE: AWG = American Wire Gauge

When working with the tool outdoors, use an extension cord that is designed for outside use. This is indicated by the letters “WA” on the cord’s jacket.

Before using an extension cord, inspect it for loose or exposed wires and cut or worn insulation.

WARNING:

Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury.

WARNING:

Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury.

ELECTRICAL CONNECTION

This tool is powered by a precision built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the saw does not operate when plugged into an outlet, double check the power supply.

SPEED AND WIRING

The no-load speed of this tool is approximately 4,800 rpm. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’s horsepower rating. A line intended only for lights cannot properly carry a power tool motor. Wire that is heavy enough for a short distance will be too light for a greater distance. A line that can support one power tool may not be able to support two or three tools.

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding pro- vides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an elec- tric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or with- out yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is neces- sary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.

Repair or replace a damaged or worn cord immediately.

This tool is intended for use on a circuit that has an outlet like the one shown in figure 1. It also has a grounding pin like the one shown.

GROUNDING

 

PIN

120V GROUNDED OUTLET

 

 

Fig. 1

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules To move into the cutting tool Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningSpeed and Wiring ElectricalExtension Cords Electrical ConnectionGlossary of Terms Features Product SpecificationsKnow Your Table SAW OverviewBlades Power SwitchOverload Reset Button Tools Needed Wrench10 mm, 11 mm Phillips Screwdriver Flathead Framing SquareLoose Parts List Key Description QtyAssembly To Install the Blade Adjusting HandleUnpacking Mounting HolesTo Check SAW Blade Installation To REMOVE/REPLACE the Throat PlateTo Install Blade Guard Assembly To Check and Align the SAW Blade and Blade Guard AssemblyOperation Cross CUT Types of CutsCutting Tips HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard Featherboard Push Stick Push BlockTo Adjust the Blade Depth To Adjust the Bevel AngleTo Adjust the Bevel Indicator Screwdriver Bevel IndicatorTo USE the Miter Gauge To Install the RIP FenceTo SET the RIP Fence Scale Indicator to the Blade Cross CUT Switch OFF Reset Button To Make a Cross CUTMiter CUT RIP CUT To Make a Miter CUTTo Make a RIP CUT Bevel Cross CUT Bevel RIP CUT To Make a Bevel Cross CUTTo Make a Bevel RIP CUT To Make a Compound Bevel Miter CUT Compound Miter CUTTo Make a NON-THROUGH CUT NON-THROUGH CUT Blade Guard Removed Push StickClamp Screw RIP Fence SAW Blade Screws Locking Handle AdjustmentsTo Check the Alignment of the RIP Fence to the Blade To SET the 45 Positive Stop Positive Stop Adjustment ScrewTo SET the 90 Positive Stop Maintenance General MaintenanceLubrication To Remove or Change the BladeTroubleshooting Problem Possible Cause SolutionService Model NO. and Serial no

BTS10 specifications

The Ryobi BTS10 is a high-performance table saw designed for both amateur woodworkers and seasoned professionals. Known for its powerful motor and solid construction, this table saw offers a blend of precision and convenience, making it an excellent choice for various woodworking tasks.

One of the standout features of the BTS10 is its robust 15-amp motor, providing ample power to handle tough cutting jobs. This motor ensures that it can effectively rip through hardwoods and softwoods alike, delivering clean and accurate cuts. The tool has a no-load speed of 5000 RPM, allowing for quick and efficient cutting, which is particularly beneficial for large-scale projects.

The BTS10 comes equipped with a spacious 27-inch aluminum table that provides ample workspace, enhancing stability and control during cuts. The table’s surface is designed to be smooth, which minimizes friction and improves accuracy. Moreover, the saw features a cast iron trunnion system that enhances stability, further contributing to the precision of cuts.

For added convenience, the Ryobi BTS10 includes a built-in blade guard and anti-kickback pawls. These safety features are essential in preventing accidents and ensuring user safety during operation. Additionally, this model also incorporates an adjustable miter gauge, allowing users to make angled cuts easily. The miter gauge slides along the table’s slots for increased accuracy when making crosscuts.

The BTS10 also supports a bevel adjustment feature that allows users to tilt the blade up to 45 degrees. This capability is ideal for making bevel cuts, providing versatility for various woodworking applications. The blade height can also be adjusted easily using a convenient handwheel, enhancing user control over cut depth.

In terms of portability, the BTS10 is designed with user convenience in mind. Although it’s built for durability, it remains relatively lightweight, making it easier to transport to job sites or storage.

Overall, the Ryobi BTS10 table saw combines power, usability, and safety features, making it a versatile tool capable of handling a range of woodworking tasks. Whether you’re a hobbyist looking to expand your workshop or a professional seeking a reliable table saw, the BTS10 delivers the performance and features required for precision woodworking.
Top Page Image Contents