Ryobi BTS10 manual Specific Safety Rules

Page 4

GENERAL SAFETY RULES

work or around or over the blade while blade is rotating. Do not attempt to remove cut material when blade is moving.

nBLADE COASTS AFTER BEING TURNED OFF.

nNEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes.

nINSPECT TOOL CORDS PERIODICALLY. If dam- aged, have repaired by a qualified service technician at an authorized service facility. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Repair or replace a damaged or worn cord immediately. Stay constantly aware of cord location and keep it well away from the rotating blade.

nINSPECT EXTENSION CORDS PERIODICALLY and replace if damaged.

nGROUND ALL TOOLS. If tool is equipped with three- prong plug, it should be plugged into a three-hole elec- trical receptacle.

nCHECK WITH A QUALIFIED ELECTRICIAN or service personnel if the grounding instructions are not completely understood or if in doubt as to whether the tool is properly grounded.

nUSE ONLY CORRECT ELECTRICAL DEVICES: 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug.

nDO NOT MODIFY the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician.

nKEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never

use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool.

nSTAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.

nDO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

nUSE ONLY CORRECT BLADES. Do not use blades with incorrect size holes. Never use blade washers or blade bolts that are defective or incorrect. The maximum blade capacity of your saw is 10 in. (254 mm).

nBEFORE MAKING A CUT, BE SURE ALL ADJUST- MENTS ARE SECURE.

nBE SURE BLADE PATH IS FREE OF NAILS. Inspect for and remove all nails from lumber before cutting.

nNEVER TOUCH BLADE or other moving parts during use.

nNEVER START A TOOL WHEN ANY ROTATING COM- PONENT IS IN CONTACT WITH THE WORKPIECE.

nDO NOT OPERATE A TOOL WHILE UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICATION.

nWHEN SERVICING use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.

nUSE ONLY RECOMMENDED ACCESSORIES listed in this manual or addendums. Use of accessories that are not listed may cause the risk of personal injury. Instructions for safe use of accessories are included with the accessory.

nDOUBLE CHECK ALL SETUPS. Make sure blade is tight and not making contact with saw or workpiece before connecting to power supply.

SPECIFIC SAFETY RULES

�n FIRMLY BOLT THE SAW TO A WORKBENCH OR LEG STAND at approximately hip height.

nNEVER OPERATE THE SAW ON THE FLOOR.

nGUARD AGAINST KICKBACK. Kickback occurs when the blade stalls rapidly and workpiece is driven back towards the operator. It can pull your hand into the blade resulting in serious personal injury. Stay out of blade path and turn switch off immediately if blade binds or stalls.

�n USE RIP FENCE. Always use a fence or straight edge guide when ripping.

nSUPPORT LARGE PANELS. To minimize risk of blade pinching and kickback, always support large panels.

nREMOVE ALL FENCES AND AUXILIARY TABLES before transporting saw. Failure to do so can result in an accident causing possible serious personal injury.

nALWAYS USE BLADE GUARD, SPREADER, AND ANTI-KICKBACK PAWLS on all “through-sawing” op-

erations. Through-sawing operations are those in which the blade cuts completely through the workpiece as in ripping or cross cutting. Keep the blade guard down, the anti-kickback pawls down, and the spreader in place over the blade.

nALWAYS SECURE WORK firmly against the rip fence or miter gauge. NEVER use the rip fence during the same operation as the miter gauge.

nALWAYS USE A PUSH STICK FOR RIPPING NAR- ROW STOCK. A push stick is a device used to push a workpiece through the blade instead of using your hands. Size and shape can vary but the push stick must always be narrower than the workpiece to prevent the push stick from contacting the saw blade. When ripping narrow stock, always use a push stick, so your hand does not come close to the saw blade. Use a featherboard and push blocks for non-through cuts.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules To move into the cutting tool Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningSpeed and Wiring ElectricalExtension Cords Electrical ConnectionGlossary of Terms Features Product SpecificationsKnow Your Table SAW OverviewOverload Reset Button Power SwitchBlades Tools Needed Wrench10 mm, 11 mm Phillips Screwdriver Flathead Framing SquareLoose Parts List Key Description QtyAssembly To Install the Blade Adjusting HandleUnpacking Mounting HolesTo Check SAW Blade Installation To REMOVE/REPLACE the Throat PlateTo Install Blade Guard Assembly To Check and Align the SAW Blade and Blade Guard AssemblyOperation Cutting Tips Types of CutsCross CUT HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard Featherboard Push Stick Push BlockTo Adjust the Blade Depth To Adjust the Bevel AngleTo Adjust the Bevel Indicator Screwdriver Bevel IndicatorTo SET the RIP Fence Scale Indicator to the Blade To Install the RIP FenceTo USE the Miter Gauge Cross CUT Switch OFF Reset Button To Make a Cross CUTTo Make a RIP CUT To Make a Miter CUTMiter CUT RIP CUT To Make a Bevel RIP CUT To Make a Bevel Cross CUTBevel Cross CUT Bevel RIP CUT To Make a Compound Bevel Miter CUT Compound Miter CUTTo Make a NON-THROUGH CUT NON-THROUGH CUT Blade Guard Removed Push StickTo Check the Alignment of the RIP Fence to the Blade AdjustmentsClamp Screw RIP Fence SAW Blade Screws Locking Handle To SET the 90 Positive Stop Positive Stop Adjustment ScrewTo SET the 45 Positive Stop Maintenance General MaintenanceLubrication To Remove or Change the BladeTroubleshooting Problem Possible Cause SolutionService Model NO. and Serial no

BTS10 specifications

The Ryobi BTS10 is a high-performance table saw designed for both amateur woodworkers and seasoned professionals. Known for its powerful motor and solid construction, this table saw offers a blend of precision and convenience, making it an excellent choice for various woodworking tasks.

One of the standout features of the BTS10 is its robust 15-amp motor, providing ample power to handle tough cutting jobs. This motor ensures that it can effectively rip through hardwoods and softwoods alike, delivering clean and accurate cuts. The tool has a no-load speed of 5000 RPM, allowing for quick and efficient cutting, which is particularly beneficial for large-scale projects.

The BTS10 comes equipped with a spacious 27-inch aluminum table that provides ample workspace, enhancing stability and control during cuts. The table’s surface is designed to be smooth, which minimizes friction and improves accuracy. Moreover, the saw features a cast iron trunnion system that enhances stability, further contributing to the precision of cuts.

For added convenience, the Ryobi BTS10 includes a built-in blade guard and anti-kickback pawls. These safety features are essential in preventing accidents and ensuring user safety during operation. Additionally, this model also incorporates an adjustable miter gauge, allowing users to make angled cuts easily. The miter gauge slides along the table’s slots for increased accuracy when making crosscuts.

The BTS10 also supports a bevel adjustment feature that allows users to tilt the blade up to 45 degrees. This capability is ideal for making bevel cuts, providing versatility for various woodworking applications. The blade height can also be adjusted easily using a convenient handwheel, enhancing user control over cut depth.

In terms of portability, the BTS10 is designed with user convenience in mind. Although it’s built for durability, it remains relatively lightweight, making it easier to transport to job sites or storage.

Overall, the Ryobi BTS10 table saw combines power, usability, and safety features, making it a versatile tool capable of handling a range of woodworking tasks. Whether you’re a hobbyist looking to expand your workshop or a professional seeking a reliable table saw, the BTS10 delivers the performance and features required for precision woodworking.
Top Page Image Contents