Bostitch manual Loadingthe N89C, To Prevent Accidental Injuries, Platform Settings

Page 6

LOADINGTHE N89C

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

TO PREVENT ACCIDENTAL INJURIES:

•Never place a hand or any other part of the body in nail discharge area of tool while the air supply is connected.

•Never point the tool at anyone else.

•Never engage in horseplay.

•Never pull the trigger unless nose is directed at the work.

•Always handle the tool with care.

•Do not pull the trigger or depress the trip mechanism while loading the tool.

1.Open the canister:

Pull down door latch and swing door/canister cover outward. Fig.A

2.Check Adjustment:

The nailer must be set for the length of nail to be used. Nails will not feed smoothly if the canister is not correctly adjusted. The canister contains an adjustable nail platform on which the nail coil rests.

The nail platform can be moved up and down to four nail settings.

To change setting pull up on the post and twist to the correct step. Fig.B

PLATFORM SETTINGS

1st Step: 2” – 2-1/2” (50 - 65mm) nails

2nd Step: 2-3/4” – 3” (70 - 75mm) nails

3rd Step: 3-1/4” – 3-1/2” (80 - 90mm) nails

3.Load the coil of nails:

Place the coil of nails over the post in the canister. Uncoil enough nails to reach the feed pawl. Place the first nail in front of the front tooth on the feed pawl, in the driver channel. The nail heads must be in the slot in the nose. Fig. C

NOTE: Use only nails recommended by BOSTITCH for N89C series nailers or nails which meet BOSTITCH specifications.

4.Swing cover closed

5.Close the door:

Check that latch engages. (If it does not engage, check that the nail heads are in the slot on the nose.)

A

B

C

-6-

Page 5 Page 7
Image 6
Page 5 Page 7
Contents N89C Introduction IndexLoadingtool Safety InstructionsAIR Supply and Connections OperationN89C Tool Specifications AIR Supplyand Connections LubricationPlatform Settings Loadingthe N89CTo Prevent Accidental Injuries Fastener Depth Control Adjustment To Adjust the Fastener Depth ControlDirectional Exhaust Deflector Sequential Trip Operation Graytrigger Tool OperationBefore Handling or Operatingthis Tool Contacttrip Conventional Operation Black TriggerContacttrip Operation Tool Operation CheckSequential Trip Operation Tool Must not CycleAIR SUPPLY-PRESSURE and Volume Replacement PartsAssembly Procedure for Seals Maintainingthe Pneumatic ToolTroubleshooting Problem Cause CorrectionCoil Nailers Introducción ÍndiceNota AL Cargar LA Herramienta Instrucciones DE SeguridadSuministro DE Airey Conexiones OperaciónMantenimiento DE LA Herramienta Especificaciones LA HerramientaLubricación Cómo Cargar EL N89C Advertencia Para Impedir Lesiones AccidentalesSelecciones DE LA Plataforma Ajuste DEL Control DE Profundidad DEL Clavo Deflector DE Escape DireccionalPara Ajustar EL Control DE Profundidad DEL Clavo Funcionamiento DE LA Herramienta FuncionamientoAntes DE Manipular U Operar Esta Herramienta Funcionamiento DEL Disparo Secuencial Funcionamiento DE LA HerramientacontinuaciónRevisión Funcional DE LA Herramienta Funcionamiento DEL Disparo DE ContactoPiezas DE Repuesto Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Procedimiento DE Ensamblaje Para LOS SellosClavadoras DE Bobina ProblemaDiagnóstico DE Falla Causa CorrecciónSommaire RemarqueChargement DE L’APPAREIL Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement FonctionnementCaractéristiques DU N89C OpérationLubrification Chargement DU N89C Pour Prévenir UN AccidentRéglage DES PLATES-FORMES Commandede Réglagede Profondeur DE Fixation Déflecteur DE L’ÉCHAPPEMENT DirectionnelPour Régler LA Profondeur DE Fixation Fonctionnement DE L’OUTIL UtilisationUtilisation DU Déclencheur Séquentiel Utilisation DE L’OUTILSUITEVérification DE L’ÉTAT DE Marche DE L’OUTIL Fonctionnement DE LA Butée DE DéclenchementPièces DE Rechange Maintenance DE L’OUTIL PneumatiquePression ET Volume DE L’ALIMENTATIOND’AIR Procédure DE Montage DES JointsProblèmes DE Fonctionnement Appareil À RouleauProblème Cause Correction

N89C specifications

The Bostitch N89C is a highly regarded pneumatic roofing nailer designed to streamline the roofing process while ensuring maximum efficiency and productivity. As a staple tool in the construction industry, particularly for roofing applications, it is engineered to handle a variety of tasks with precision and ease, making it a favorite among both professionals and DIY enthusiasts.

One of the standout features of the Bostitch N89C is its lightweight design, weighing in at an impressive 4.6 pounds. This reduced weight allows for extended use without excessive fatigue, which is crucial during long working hours on steep roofs. The nailer is constructed with a durable housing that can withstand the rigors of job sites, ensuring longevity and reliable performance.

The N89C operates using a pneumatic system that delivers a powerful and consistent driving force. It is capable of accommodating wire-weld and plastic collated nails ranging from 3/4 inch to 1-3/4 inch in length, offering versatility for various roofing materials, from shingles to plywood. This adaptability makes it an essential tool for contractors who need to switch between different materials and tasks seamlessly.

Equipped with a depth adjustment feature, the Bostitch N89C allows users to control the depth at which nails are driven, ensuring proper fastening without damaging the roofing materials. This precision is vital for maintaining the integrity of roofs and ensuring longevity. An adjustable exhaust port also enhances user comfort by directing air away from the user, reducing the chance of dust and debris being blown back onto the work surface.

The Bostitch N89C's magazine holds up to 100 nails, enabling contractors to work efficiently without frequent reloading. This feature is complemented by a nail lock-out mechanism that prevents dry firing, which can cause damage to the tool and materials. The easy-to-clear jam release lever also ensures that any jams can be resolved quickly, minimizing downtime on the job.

Incorporating advanced technologies like an efficient air consumption design, the Bostitch N89C promotes longer run times and reduced compressor cycling. This innovation not only improves performance but also contributes to cost-effectiveness for contractors who rely on pneumatic tools for their jobs.

In summary, the Bostitch N89C roofing nailer is a powerful, reliable, and easy-to-use tool built for professionals. With its lightweight structure, adjustable features, and durable construction, it offers the performance needed to tackle roofing projects efficiently and effectively, making it an invaluable addition to any contractor's toolkit.
Top Page Image Contents