Manuals / Lucent Technologies / Computer Equipment / Network Router

Lucent Technologies 7820-0657-001 manual Setting the data transmission rate, Rate, DIP Switch

Models: 7820-0657-001

1 34

Download 34 pages 17.95 Kb

Page 17

Image 17

Setting up the DSLPipe DSU

Setting the data transmission rate

To set the DSLPipe DSU data transmission rate, use a pen to move the DIP switches.Table 2-1 shows the DIP switch settings for each rate. Move the DIP switch down to turn the switch on. Move a switch up to turn it off.

Table 2-1. Data transmission settings

Rate	DIP Switch 1	DIP Switch 2	DIP Switch 3

144 Kbps	ON	ON	ON

272 Kbps	ON	ON	OFF

400 Kbps	ON	OFF	ON

528 Kbps	ON	OFF	OFF

784 Kbps	OFF	ON	ON

1168 Kbps	OFF	ON	OFF

1552 Kbps	OFF	OFF	ON

2320 Kbps	OFF	OFF	OFF

Configuring the unit as either CPE or COE

If you want the DSLPipe DSU to function as a CPE, leave the fourth DIP switch in the up (off) position. If you want the unit to function as a COE, move the fourth DIP switch down.

Note: JP3 and JP4 must be installed for Dip Switch 4 to be functional.

DSLPipe DSU (SDSL) User’s Guide

2-3

Page 17

Image 17

Lucent Technologies 7820-0657-001 Setting the data transmission rate, Configuring the unit as either CPE or COE, Rate

Contents

Part Number For software version October DSLPipe DSU SDSLUser’s Guide Copyright 1999 Lucent Technologies. All Rights Reserved Lucent TechnologiesTrademarks Ordering InformationCustomer Service Customer ServiceFinding information and software on the Internet Obtaining technical assistanceOther telephone numbers Priority Technical AssistanceCalling Lucent from outside the United States Obtaining assistance through correspondenceImportant safety instructions Important safety instructionsImportant safety instructions Important safety instructions Important safety instructions Installation ContentsViewing configuration information Hardware SpecificationsPage Introduction Wire gaugeTable 1-1. DSLPipe DSU transmission rate Data Transmission Rate in KbpsDSLPipe DSU configuration DSLPipe DSU featuresDSLPipe DSU features Figure 1-1. Example Using a DSLPipe DSU as CPEDSLPipe DSU architecture Figure 1-2. Example Using a DSLPipe DSU as COEDSLPipe DSU architecture Figure 1-3. DSLPipe DSU architecturePage 4 DSLPipe DSU SDSL User’s Guide InstallationChecking package contents Setting up the DSLPipe DSU Setting up the DSLPipe DSUFigure 2-1. Package contents DC INConfiguring the unit as either CPE or COE Setting the data transmission rateTable 2-1. Data transmission settings DIP SwitchConnecting the cables Connecting the cablesTable 2-2. CPE vs. COE configuration ConfigurationDSLPipe DSU SDSL User’s Guide Figure 2-3. Location of the LED lights in the DSLPipe DSU front panelPage Items you need Viewing configuration informationConnecting serial cable and setting up communications software Terminal type Specify VT100 Connecting serial cable and setting up communications softwareBits per second Specify Data bits Specify Stop bits SpecifyViewing configuration information Viewing configuration informationFigure 3-1. DSLPipe configuration window Table 3-1. Fields in the DSLPipe status windowViewing configuration information Table 3-1. Fields in the DSLPipe status window ContinuedFields DescriptionViewing diagnostic information Viewing diagnostic informationFigure 3-2. Debug Mode window Table 3-1. Fields in the DSLPipe status window ContinuedViewing diagnostic information Table 3-2. Fields in the HDLC Registers listFields DescriptionViewing diagnostic information Table 3-2. Fields in the HDLC Registers list ContinuedFields DescriptionPage Table A-1. DSLPipe DSU specifications Hardware SpecificationsPage Warranties and FCC Regulations Product warrantyOut-of warranty repair Warranty repairFCC Part 15 Notice Warranties and FCC RegulationsWarranties and FCC Regulations IC CS-03 NoticeIC CS-03 Notice

Setting the data transmission rate

Table 2-1. Data transmission settings

Rate

DIP Switch 1

Configuring the unit as either CPE or COE