Hobart OM-1581 manual Water-Cooled Gun Connections

Page 18

3-7. Water-Cooled Gun Connections

4 3

5

Left Side

3

2

1

7

8

6

1 Gas Hose

Connect to Gas fitting on feeder.

2 Water Hose

Connect to Water To Gun fitting on feeder (left-hand threads).

3Wire Conduit

4Thumbscrew

5Wire Conduit Block

Loosen thumbscrew, and insert conduit through Wire opening until it bottoms against block. Tighten thumbscrew.

6 Gun Control Cable

Insert plug into Gun Control recep- tacle, and tighten threaded collar.

7 Strain Relief

Remove strain relief as shown.

8 Power/Water Cable

Route cable through strain relief and connect to Weld/Water From Gun outlet on feeder. Reinstall strain relief. Close and latch door.

Tools Needed:

5/8, 1-1/8 in

Ref. 151 778-B / 152 456-A

OM-1581 Page 14

Image 18
Contents OM-1581 ProcessesDescription From Hobart to You Table of Contents Page Electric Shock can kill Symbol UsageArc Welding Hazards Fumes and Gases can be hazardousFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killPrincipal Safety Standards EMF Information About PacemakersUN Choc É Lectrique peut tuer Signification des symbolesConsignes DE Securite Lire Avant Utilisation LES Fumé ES ET LES GAZ peuvent ê tre dangereuxLE Soudage peut provoquer un incendie ou une explosion DES Particules Volantes peuvent blesser les yeuxLE Bruit peut affecter l’ouïe ’EMPLOI Excessif peut Risque D’INCENDIE OULA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sé curité Information sur les champs é lectromagné tiquesGun Specifications SpecificationsWire Feeder Specifications Duty Cycle And OverheatingInstallation Constant Voltage CV Weld- ing Power Source Plug Removing Top Cover Of Gun Air-Cooled Gun Connections Water-Cooled Gun Connections Air-Cooled Feeder Connections Water-Cooled Feeder Connections Rear Of Water Fitting Left- Hand ThreadsAdjusting Contact Tip Position Voltage Sensing Lead Connections12 VAC/Contactor Control Plug Information ContactorPLG5 Installing Wire Spool Threading Welding Wire Through Feeder Threading Welding Wire Through Gun Coolant GuidelinesAdjusting Wire Feed Starting Speed Front Panel Controls Of Feeder Air-Cooled Model Shown Safety EquipmentOperation Work And Voltage Sensing Cable ClampsJog Switch Voltage/Wire Speed Switch And Meter OptionalRun-In Speed Control Remote Voltage Control Optional Power Switch Spot Controls OptionalFlowmeter Optional Internal ControlsCoolant Supply For Water-Cooled Models Only Gun ControlsShielding Gas Sequence Of Gas Metal Arc Welding Gmaw Continuous Or SpotMaintenance & Troubleshooting Routine MaintenanceMonths Changing Or Cleaning Gun Drive Roll Changing Feeder Drive Roll And Wire Inlet Guide Replacing Or Cleaning Gun Drive Roll Bearing Replacing Or Cleaning Feeder Drive Roll BearingChanging Gun Contact Tip And Liner Removing Contact Tip Adapter In Air-Cooled ModelsReplacing Hub Assembly Removing Contact Tip Adapter In Water-Cooled ModelsAdjusting Hub Tension Water Flow Switch Optional For Water-Cooled ModelsOverload Protection Troubleshooting Wire Feeder TroubleGun Trouble Electrical Diagrams Circuit Diagram For Wire FeederCircuit Diagram For Gun Parts List Main AssemblyDia Part CB1 Motor & Wire Drive -1 Item Panel, Front w/Components Water-Cooled Model Illustrated Panel, Front w/Components -1 Item Exploded View Of Gun 133 203 Barrel Assembly -4 Item Optional Call HOBART1 for your local Hobart distributor Contact your Distributor for Hobart Welding Products