Hobart Welding Products 187 manual Optional Drive Rolls, Options

Page 50

10-3. Optional Drive Rolls

 

For All Feed Head Assemblies

 

 

 

PART NO.

 

WIRE DIAMETER

 

INCHES (mm)

 

 

 

 

 

237 338

 

.023/.025 (.6) and .030/.035 (.8 and .9)

 

 

 

202 926

 

.030/.035 (.8 and .9) and .045 (1.2 VK Groove)

 

 

 

10-4. Options

PART NO.

DESCRIPTION

REMARKS

 

 

 

770 187

Running Gear/Cylinder Rack

For One Small Gas Cylinder, 100 lb (45 kg) max.

 

 

 

194 776

Small Running Gear/Cylinder Rack

For One Small Gas Cylinder, 75 lb (34 kg) max.

 

 

 

246 800

H100S2-10 Replacement Gun

10 ft length/.030-.035 wire size

 

 

 

195 186

Protective Cover

Weatherproof nylon

 

 

 

212 492

Regulator/Flowmeter

For use with CO2 shielding gas, 10−50 CFH

144 108

Gas Hose 5 ft

For use with regulator/flowmeter 212 492

 

 

 

NOTE: If individual parts are required, see Parts List chapter of this manual for part number to order.

OM-228 187 Page 46

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Description OM-228 187BProcesses 2010−01From Hobart to You Protect Your InvestmentTable of Contents − Parts List Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can burnWelding can cause fire or explosion Fumes and Gases can be hazardousARC Rays can burn eyes and skin Flying Metal or Dirt can injure eyesFalling Equipment can injure Welding Wire can injureFire or Explosion hazard Moving Parts can injureEMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLE Soudage peut provoquer un incendie ou une explosion LES Pièces Chaudes peuvent provoquer des brûluresLES Fumées ET LES GAZ peuvent être dangereux Risque D’INCENDIE OU LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées LA Chute DE L’ÉQUIPEMENT peut provoquer des blessuresLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLes Pièces Mobiles peuvent causer des blessures LE Soudage À L’ARC risque de provoquer des interférencesEn ce qui concerne les implants médicaux Principales normes de sécuritéInformations relatives aux CEM OM-228 187 Specifications − SpecificationsSymbols And Definitions − DefinitionsAmperes Duty Cycle And OverheatingVolt-Ampere Curves OutputInstalling Welding Gun − InstallationInstalling Nozzle, Contact Tip, And Adapter Installing Work Clamp Changing Polarity Turn off welding power sourceProcess/Polarity Table Installing Gas Supply Selecting a Location And Connecting Input Power Electrical Service Guide Installing Wire Spool And Adjusting Hub TensionThreading Welding Wire Hold wire tightly to keep it from unraveling− Operation ControlsOM-228 187 Weld Parameter Chart CFH227010 Overload Protection − Maintenance & TroubleshootingRoutine Maintenance Drive Motor ProtectionChanging Drive Roll Or Wire Inlet Guide Thread wire according to Replacing Switch And/Or Head Tube Troubleshooting Table Trouble RemedyOM-228 187 − Electrical Diagram Circuit Diagram228 180-A − MIG Welding Gmaw Guidelines Typical MIG Process ConnectionsSelect Voltage Typical MIG Process Control SettingsWire Size Amperage Range Holding And Positioning Welding Gun Groove WeldsConditions That Affect Weld Bead Shape Gun Movement During Welding Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Troubleshooting − Excessive Penetration Troubleshooting − Excessive SpatterTroubleshooting − Porosity Possible Causes Corrective ActionsTroubleshooting − Burn-Through Troubleshooting − Lack Of PenetrationTroubleshooting − Incomplete Fusion Troubleshooting − Waviness Of Bead Troubleshooting − DistortionApplication Troubleshooting Guide For Semiautomatic Welding EquipmentCommon MIG Shielding Gases Welding arc not stable Wire slipping in drive rolls − Parts List Main AssemblyDia Part Description Quantity 228 H100S2-10 Gun 245Optional Drive Rolls OptionsAssistance ServiceSupport Contact your Distributor for Hobart Welding Products
Top Page Image Contents