Hobart Welding Products 187 manual Fire or Explosion hazard, Falling Equipment can injure

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.

FALLING EQUIPMENT can injure.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

DKeep equipment (cables and cords) away from moving vehicles when working from an aerial location.

DFollow the guidelines in the Applications Manual for the Revised NIOSH Lifting Equation (Publication No. 94−110) when manu- ally lifting heavy parts or equipment.

MOVING PARTS can injure.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards closed and securely in place.

DHave only qualified persons remove doors, panels, covers, or guards for maintenance and troubleshooting as necessary.

DReinstall doors, panels, covers, or guards when maintenance is finished and before reconnecting input power.

READ INSTRUCTIONS.

DRead and follow all labels and the Owner’s Manual carefully before installing, operating, or servicing unit. Read the safety information at the beginning of the manual and in each section.

DUse only genuine replacement parts from the manufacturer.

DPerform maintenance and service according to the Owner’s Manuals, industry standards, and national, state, and local codes.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

FLYING SPARKS can injure.

D Wear a face shield to protect eyes and face.

D Shape tungsten electrode only on grinder with proper guards in a safe location wearing proper face, hand, and body protection.

DSparks can cause fires — keep flammables away.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can injure.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can injure.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

OM-228 187 Page 3

Image 7
Contents 2010−01 OM-228 187BProcesses DescriptionProtect Your Investment From Hobart to YouTable of Contents − Parts List HOT Parts can burn Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can injure Welding Wire can injureFire or Explosion hazard Falling Equipment can injureAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux LES Pièces Chaudes peuvent provoquer des brûluresLE Soudage peut provoquer un incendie ou une explosion LA Chute DE L’ÉQUIPEMENT peut provoquer des blessures LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OULE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLes Pièces Mobiles peuvent causer des blessures LES Fils DE Soudage peuvent provoquer des blessuresInformations relatives aux CEM Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-228 187 − Definitions − SpecificationsSymbols And Definitions SpecificationsOutput Duty Cycle And OverheatingVolt-Ampere Curves AmperesInstalling Nozzle, Contact Tip, And Adapter − InstallationInstalling Welding Gun Installing Work Clamp Process/Polarity Table Turn off welding power sourceChanging Polarity Installing Gas Supply Selecting a Location And Connecting Input Power Installing Wire Spool And Adjusting Hub Tension Electrical Service GuideHold wire tightly to keep it from unraveling Threading Welding WireControls − OperationOM-228 187 CFH Weld Parameter Chart227010 Drive Motor Protection − Maintenance & TroubleshootingRoutine Maintenance Overload ProtectionChanging Drive Roll Or Wire Inlet Guide Thread wire according to Replacing Switch And/Or Head Tube Trouble Remedy Troubleshooting TableOM-228 187 Circuit Diagram − Electrical Diagram228 180-A Typical MIG Process Connections − MIG Welding Gmaw GuidelinesWire Size Amperage Range Typical MIG Process Control SettingsSelect Voltage Groove Welds Holding And Positioning Welding GunConditions That Affect Weld Bead Shape Good Weld Bead Characteristics Poor Weld Bead CharacteristicsGun Movement During Welding Possible Causes Corrective Actions Troubleshooting − Excessive SpatterTroubleshooting − Porosity Troubleshooting − Excessive PenetrationTroubleshooting − Incomplete Fusion Troubleshooting − Lack Of PenetrationTroubleshooting − Burn-Through Troubleshooting − Distortion Troubleshooting − Waviness Of BeadCommon MIG Shielding Gases Troubleshooting Guide For Semiautomatic Welding EquipmentApplication Welding arc not stable Wire slipping in drive rolls Main Assembly − Parts ListDia Part Description Quantity 228 245 H100S2-10 GunOptions Optional Drive RollsSupport ServiceAssistance Hobart Welding Products Contact your Distributor for