Hobart Welding Products 217 694E manual Cleaning Or Replacing Gun Liner, Disconnect gun from unit

Page 32

.A complete Parts List is available at www.HobartWelders.com

7-6. Cleaning Or Replacing Gun Liner

! Disconnect gun from unit.

Head Tube

10 mm

Remove liner.

8 mm

Remove nozzle, contact tip, adapter, gas diffuser, and wire outlet guide.

Blow out gun casing.

Lay gun cable out straight before installing new liner.

To Reassemble Gun:

Insert new liner.

Install wire outlet guide so that 1/8 in (3 mm) of liner sticks out. Hand tighten outlet guide, and then tighten two full turns more.

Cut liner off so that 3/4 in (19 mm) sticks out of head tube.

Install gas diffuser, adapter, contact tip, and nozzle.

Tools Needed:

8 mm / 10mm

Ref. 802 446-A

OM-925 Page 28

Image 32

Contents Arc Welding Power Source Wire Feeder ProcessesDescription OM-925217 694E 2008−10From Hobart to You Protect Your InvestmentTable of Contents − ACCESSORIES/CONSUMABLES Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesIndique des instructions spécifiques Symboles utilisésUNE Décharge Électrique peut entraîner la mort LE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-925 − Specifications Symbols And DefinitionsSpecifications − DefinitionsWarranty Duty Cycle And OverheatingOutput Duty Cycle % Can damage unit or gun and voidVolt-Ampere Curves Voltage15.0 10.0 100 110 120 130 140 150 160− Installation Installing Welding GunInstalling Work Clamp Be sure that gun end is tight against drive assemblyProcess/Polarity Table Changing PolarityInstalling Gas Supply Feedhead Pressure Assembly OpenFeedhead Pressure Assembly Closed Do not use Argon/Mixed gas regulator/flowmeterSelecting a Location And Connecting Input Power Do not move or operate unit Where it could tipRetaining ring used with 8 in 203 mm spool only Installing Wire Spool And Adjusting Hub TensionAlign locking hole in spool with locking pin on spool hub Use with solid or flux cored wire Installing Contact Tip And NozzleTurn off welding power source Lay gun cable out straight Threading Welding WireHold wire tightly to keep it from unraveling With a setting of 2 or 3 on the scale Pressure Indicator ScaleTighten Desired drive roll pressure. StartControls Source or -2. Do not switch under load− Operation Material Thickness Reference Chart Weld Parameter Chart 217 618-A − Maintenance & Troubleshooting Routine MaintenanceOverload Protection Drive Motor ProtectionChanging Drive Roll Or Wire Inlet Guide Turn Off power before replacing contact tipReplacing Gun Contact Tip Stamped Stamped .030/.035To Reassemble Gun Cleaning Or Replacing Gun LinerDisconnect gun from unit Replacing Switch And/Or Head Tube Troubleshooting Table Trouble Remedy− Electrical Diagram Circuit DiagramWire Feeder Power Source Shielding Gas − MIG Welding Gmaw GuidelinesTypical MIG Process Connections Regulator FlowmeterTypical MIG Process Control Settings Wire Size Amperage Range001 in = 1 ampere 125 in = 125 aHolding And Positioning Welding Gun Groove WeldsConditions That Affect Weld Bead Shape Push Perpendicular DragShort Normal Long Slow Normal FastGun Movement During Welding Poor Weld Bead CharacteristicsGood Weld Bead Characteristics Troubleshooting − Excessive Spatter Troubleshooting − PorosityTroubleshooting − Excessive Penetration Possible Causes Corrective ActionsTroubleshooting − Burn-Through Troubleshooting − Lack Of PenetrationTroubleshooting − Incomplete Fusion Troubleshooting − Waviness Of Bead Troubleshooting − DistortionBase metal to move DirectionApplication Troubleshooting Guide For Semiautomatic Welding EquipmentCommon MIG Shielding Gases Welding arc not stable Wire slipping in drive rolls Readjust welding parametersWelding power source Drive rolls if necessary− ACCESSORIES/CONSUMABLES AccessoriesReplacement Drive Rolls ConsumablesAssistance ServiceSupport Contact your Distributor for Hobart Welding Products