Bostitch BTFP71875 manual Fastener JAM Clearing, Tool Operation Check

Page 5

TOOL OPERATION

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1/CAN/CSA Z94.3 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

BEFORE HANDLING OR OPERATING THIS TOOL:

READ AND UNDERSTAND THE WARNINGS CONTAINED IN THIS MANUAL.

BOSTITCH OFFERS ONE TYPE OF OPERATION FOR THE BTFP71875 SERIES TOOLS, TRIGGER OPERATION WITH SECONDARY TRIGGER

OPERATION

TRIGGER OPERATION WITH A SECONDARY TRIGGER:

When the secondary trigger is pulled, the tool will actuate each time the trigger is pulled. This trigger operated tool is operated by first pulling or grasping the secondary trigger under the hand grip, followed by pulling the trigger under the valve as shown Fig. 5.

Never inadvertently pull or grasp the secondary trigger when moving about, changing work location, when holstering or hanging tool, or when preparing work surface for fastening operation.

The operator must not hold the secondary trigger pulled except during fastening operation as serious injury could result if the trigger accidentally contacts someone or something, causing the tool to cycle.

Fig.5

PULL TRIGGER

PULL OR GRASP THIS SECONDARY

 

TRIGGER FIRST

 

 

FASTENER JAM CLEARING

ALWAYS DISCONNECT THE TOOL FROM AIR SUPPLY BEFORE CLEARING A JAMMED FASTENER.

TO CLEAR A JAMMED FASTENER:

1.Release the magazine and pull it back.

2.Remove Jammed fastener

USING THE OPTIONAL BELT HOOK (SOLD SEPERATELY)

Always disconnect tool from air supply when making adjustments or servicing.

The operator must not hold the secondary trigger pulled except during fastening operation as serious injury could result if the trigger accidentally contacts someone or something, causing the tool to cycle.

Never inadvertently pull or grasp the secondary trigger when moving about, changing work location, when holstering or hanging tool, or when preparing work surface for fastening operation.

TOOL OPERATION CHECK:

Remove all fasteners from tool before performing tool operation check.

TRIGGER OPERATION WITH A SECONDARY TRIGGER:

The trigger will only actuate the tool if the secondary trigger has already been pulled.

The secondary trigger is located under the handle. The secondary trigger prevents the primary trigger from actuating the tool if the secondary trigger has not been pulled first.

-5-

Image 5
Contents BTFP71875 Safety Instructions Definitions Safety GuidelinesIntroduction IndexAIR Supply and Connections Tool SpecificationsOperation Maintaining the ToolLoading Loading the BTFP71875AIR Consumption Tool Operation Using the Optional Belt Hook Sold SeperatelyFastener JAM Clearing Tool Operation CheckReplacement Parts Trouble ShootingAIR SUPPLY-PRESSURE and Volume Problem Cause CorrectionÍndice IntroducciónNota Pautas DE Seguridad / DefinicionesOperación Suministro DE Aire Y ConexionesMantenimiento DE LA Herramienta Especificaciones DE LA HerramientaConexión DE Aire DE LA Herramienta Cómo Cargar EL BTFP71875Presión DE Operación Consumo DE AireCarga Operación DE LA HerramientaAntes DE Manejar U Operar Esta Herramienta Funcionamiento CON Gatillo SecundarioUSA EL Gancho Para Cinturón Opcional SE Vende POR Separado Eliminación DE Atascos DE PasadoresVerificación DE LA Operación DE LA Herramienta Mantenimiento DE LA Herramienta NeumáticaCausa ProblemaDiagnóstico DE Falla Mesures DE Sécurité Définitions SommaireRemarque Alimentation EN AIR Comprimé ET Raccordement Consignes DE SécuritéOpération Entretien DE L’APPAREILChargement DU BTFP71875 Alimentation Dair ET ConnexionsChargement Fonctionnement DE L’OUTILUtilise LE Crochet DE Ceinture Optionnel Vendu Séparément Dégagement Dune AttacheVérification DU Fonctionnement DE Loutil Fonctionnement DE LA Gâchette Avec LA Gâchette SecondaireEntretien DE L’OUTIL Pneumatique Alimentation D’AIR Pression VolumeDépannage Problème Cause Correction