Enerco MHBF10LP Cleaning and Maintenance, Cleaning ODS/PILOT and Burner, Cleaning Heater Cabinet

Page 13

Figure 24a

Figure 24b

CLEANING AND MAINTENANCE

WARNING: Turn off heater and let cool before servicing.

CAUTION: You must keep control areas, burner and circulation air passageways of heater clean. Inspect these areas of heater before use. Have the heater inspected yearly by a qualified service person. Heater may need more frequent cleaning due to excess lint from carpeting, bedding material, pet hair, etc.

Make sure grille guard is in place before running heater. If screen or grille guard is removed for servicing it must be replaced prior to operating the heater.

WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.

CLEANING ODS/PILOT AND BURNER

•Use as vacuum cleaner, pressurized air or small soft bristled brush to clean.

CLEANING BURNER PILOT AIR HOLE INLET

We recommend that you clean the unit every 2,500 hours of operation or every three months. We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 psig.

This can be done by using a vacuum cleaner in the blow position, using compressed air in a can, please follow the directions on the can. If you don’t follow directions on the can you could damage the burner or pilot assem- bly. In addition, the directions that follow should also be followed.

1.Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

2.Inspect burner and pilot for dust and dirt.

3.Blow air through the port/slots and holes in the burner.

A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. To clean the pilot assembly find the small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see figure 25). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if com- pressed air is not available.

Figure 25

CLEANING HEATER CABINET

Air passageways

•Use a vacuum cleaner or pressurized air to clean

Exterior

•Use a soft cloth dampened with a mild soap and water mixture. Wipe the cabinet to remove dust.

13Installation instructions and Owner’s Manual

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model # Burn Rate Blue Flame Heaters Plaque HeatersWhat to do if YOU Smell GAS Carbon Monoxide Poisoning PrecautionsPropane/LP Gas Thermostatic Control on Thermostat Models Safety DeviceLocal Codes Ignition SystemVentilation AIR Determining the Type of Heater Location SpaceVentilation from Inside Building Locating Heater InstallationVentilation from Outdoors Check GAS TypeMounting Bracket Fastening Heater to WallInstalling Support Feet see figure Installing Bottom Mounting ScrewsConnecting to GAS Supply Placing Heater on Mounting BracketTest Pressure Equal To or Less Than ½ psig 3.5 kPa Test pressure in Excess of ½ psig 3.5kPaElectrical Wiring Diagram Pressure Testing Heater Gas ConnectionsOperating Your Heater What to do if YOU Smell GASFor IR Heaters only Lighting InstructionsShutting OFF Heater To Turn OFF GAS to ApplianceShutting OFF Burner only Pilot Stays LIT Turn control knob clockwise to the PILOT/IGN positionInspecting Burner Thermostat Control OperationPilot Flame Pattern Burner Flame PatternCleaning ODS/PILOT and Burner Cleaning and MaintenanceCleaning Burner Pilot AIR Hole Inlet Cleaning Heater CabinetObserved Symptom Possible Cause Remedy TroubleshootingControl knob not in pilot position Observed Symptom Possible Cause Remedy Troubleshooting CON’TIR10 LP IR20LPT IR30LPT SpecificationsBF10LP BF20LPT BF30LPT Parts Under Warranty Replacement PartsParts not Under Warranty Technical ServiceBF20LPT BF30LPT Thermostat modelsIR20LPT IR30LPT Thermostat models Parts ListIR20LPT, IR30LPT, BF20LPT, BF30LPT IR20LPT BF20LPT IR30LPT BF30LPT70683 Not sold separately Must purchase Assembly Items not shown70684 31-1 70685BF10LP NON-Thermostat models IR10LPIR10LP, BF10LP, IR10 LP, BF10LP Non-Thermostat modelDescription QTY IR10LP BF10LPDescription QTY Keep this warranty Warranty InformationModel Serial No Date Purchased Ansi Z21.11.2b-2004
Related manuals
Manual 24 pages 60.62 Kb Manual 24 pages 35.26 Kb

MHBF20LPT, TSBF20LPT, MHBF10LP, TSBF10LP, HSBF20LPT specifications

The Enerco MHBF10LP, TSBF10LP, HSBF10LP, HSBF20LPT, and TSBF20LPT are innovative heating solutions designed for both commercial and residential applications. These units are highly efficient gas-fired heaters offering versatile heating capabilities, ensuring user comfort in various settings.

The MHBF10LP is a liquid propane heater featuring a powerful output of 10,000 BTU. It operates with a direct ignition system, allowing for quick and reliable startups. Its compact design makes it suitable for smaller spaces, while the adjustable heat settings empower users to customize their warmth. The MHBF10LP boasts a safety shut-off system which enhances the overall safety of the unit.

In contrast, the TSBF10LP is engineered for portability, offering the same 10,000 BTU output but with added mobility features. It comes with a built-in carrying handle and lightweight design, making it easy to transport from one location to another. Perfect for job sites or outdoor events, it features a sturdy construction that withstands demanding environments and a direct ignition system for ease of use.

The HSBF10LP, another variant in this range, offers high-efficiency heating in a small footprint. This model stands out with its integrated fan that aids in even heat distribution. Users can quickly warm up spaces without the long wait times. Additionally, it provides options for permanent installation, making it an adaptable choice for various applications.

The HSBF20LPT and TSBF20LPT models deliver enhanced power with a heating capacity of 20,000 BTU. The HSBF20LPT focuses on high efficiency and user convenience, featuring an automatic thermostat control to maintain desired temperatures without constant adjustment. Its robust design is perfect for larger areas, ensuring consistent warmth and comfort.

On the other hand, the TSBF20LPT is portable like its 10,000 BTU counterpart but with double the capacity. Its rugged construction and portability make it ideal for both indoor and outdoor use. The unit's reliability in diverse conditions is coupled with an ease of operation, providing warmth where it's most needed.

All models in this Enerco range prioritize user safety and efficiency. Featuring built-in safety mechanisms such as flame failure protection and tip-over shut-off systems, each heater ensures safe operation. Furthermore, the robust construction and high-quality materials used in these devices promise durability, making them a worthwhile investment for long-term heating needs.

Overall, Enerco's MHBF and TSBF series heaters represent a blend of modern technology, safety features, and user-friendly designs, tailored for a variety of heating applications.
Top Page Image Contents