Enerco TSBF10LP, MHBF10LP, HSBF10LP, HSBF20LPT, MHBF20LPT Fastening Heater to Wall, Mounting Bracket

Page 6

36” min. from

6” Min from ceiling adjoining

walls

Left

SideRight

Side

Floor

2” min. to top surface of carpet, tile or other combustible material

Figure 4

FASTENING HEATER TO WALL

Mounting Bracket

The mounting bracket in located on the back panel of heater (see figure 5). It has been taped there for shipping. Remove mounting bracket from back panel.

Mounting

Bracket

Figure 5

Removing Front Panel of Heater

1.Remove three screws on bottom front of front panel.

2.Pull bottom of front panel forward, then down (see figure 6)

Figure 6

Attaching Mounting Bracket to Wall

Use holes on each end of mounting bracket to attach bracket to wall. These holes are 16 inches apart. Attach mounting bracket to wall in one of two following ways.

1.Attach to wall studs

2.Attach to wall anchor

Attaching to Wall Stud:

This way is the best providing the strongest mounting in wood frame houses.

Attaching to Wall Anchor:

This way allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which way best suits your needs. Either method will provide a secure hold for the mounting bracket.

1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level. For wall stud mounting locate one end of the mounting bracket over a wall stud.

WARNING: Maintain minimum clearances shown in figure 7. If you can, provide greater clearances from the floor and joining wall.

2.Mark screw locations on wall (see figure 7).

3.Remove tape and mount bracket from wall.

6-1/2” Min. 10,000 BTU

10-1/4” min 20,000-30,000 BTU

Wall

 

 

 

 

 

 

16” (Lg)

 

 

 

Adjoining

Mark

locations

 

 

mounting hole

 

 

 

 

12-9/64” (Sm)

 

17-1/2” Min.

 

and drill holes where indicated.

 

 

 

 

Allow for minimum clearances

 

 

 

 

 

Figure 7

Attaching to Wall Stud:

For attaching mounting bracket to wall studs

1.Drill holes at marked locations using 9/64” drill bit.

2.Place mounting bracket onto wall. Line up holes on each end of bracket with hole drilled in wall.

3.Insert mounting screws through bracket and into wall studs.

4.Tighten screws until mounting bracket is firmly fastened to wall studs.

Attaching to Wall using Anchor:

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or ma- sonry)

Note: Wall anchors, mounting screws, and spacer are in hardware package. The hardware package is provided with heater.

6 Installation instructions and Owner’s Manual 70575 Rev. E 04/07

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Blue Flame Heaters Plaque Heaters Model # Burn RateWhat to do if YOU Smell GAS Precautions Carbon Monoxide PoisoningPropane/LP Gas Local Codes Safety DeviceThermostatic Control on Thermostat Models Ignition SystemDetermining the Type of Heater Location Space Ventilation AIRVentilation from Inside Building Ventilation from Outdoors InstallationLocating Heater Check GAS TypeFastening Heater to Wall Mounting BracketConnecting to GAS Supply Installing Bottom Mounting ScrewsInstalling Support Feet see figure Placing Heater on Mounting BracketTest pressure in Excess of ½ psig 3.5kPa Test Pressure Equal To or Less Than ½ psig 3.5 kPaOperating Your Heater Pressure Testing Heater Gas ConnectionsElectrical Wiring Diagram What to do if YOU Smell GASLighting Instructions For IR Heaters onlyShutting OFF Burner only Pilot Stays LIT To Turn OFF GAS to ApplianceShutting OFF Heater Turn control knob clockwise to the PILOT/IGN positionPilot Flame Pattern Thermostat Control OperationInspecting Burner Burner Flame PatternCleaning Burner Pilot AIR Hole Inlet Cleaning and MaintenanceCleaning ODS/PILOT and Burner Cleaning Heater CabinetTroubleshooting Observed Symptom Possible Cause RemedyControl knob not in pilot position Troubleshooting CON’T Observed Symptom Possible Cause RemedySpecifications IR10 LP IR20LPT IR30LPTBF10LP BF20LPT BF30LPT Parts not Under Warranty Replacement PartsParts Under Warranty Technical ServiceThermostat models BF20LPT BF30LPTIR20LPT IR30LPT IR20LPT, IR30LPT, BF20LPT, BF30LPT Parts ListThermostat models IR20LPT BF20LPT IR30LPT BF30LPT70684 Not sold separately Must purchase Assembly Items not shown70683 31-1 70685NON-Thermostat models IR10LP BF10LPDescription QTY Non-Thermostat modelIR10LP, BF10LP, IR10 LP, BF10LP IR10LP BF10LPDescription QTY Model Serial No Date Purchased Warranty InformationKeep this warranty Ansi Z21.11.2b-2004
Related manuals
Manual 24 pages 60.62 Kb Manual 24 pages 35.26 Kb

MHBF20LPT, TSBF20LPT, MHBF10LP, TSBF10LP, HSBF20LPT specifications

The Enerco MHBF10LP, TSBF10LP, HSBF10LP, HSBF20LPT, and TSBF20LPT are innovative heating solutions designed for both commercial and residential applications. These units are highly efficient gas-fired heaters offering versatile heating capabilities, ensuring user comfort in various settings.

The MHBF10LP is a liquid propane heater featuring a powerful output of 10,000 BTU. It operates with a direct ignition system, allowing for quick and reliable startups. Its compact design makes it suitable for smaller spaces, while the adjustable heat settings empower users to customize their warmth. The MHBF10LP boasts a safety shut-off system which enhances the overall safety of the unit.

In contrast, the TSBF10LP is engineered for portability, offering the same 10,000 BTU output but with added mobility features. It comes with a built-in carrying handle and lightweight design, making it easy to transport from one location to another. Perfect for job sites or outdoor events, it features a sturdy construction that withstands demanding environments and a direct ignition system for ease of use.

The HSBF10LP, another variant in this range, offers high-efficiency heating in a small footprint. This model stands out with its integrated fan that aids in even heat distribution. Users can quickly warm up spaces without the long wait times. Additionally, it provides options for permanent installation, making it an adaptable choice for various applications.

The HSBF20LPT and TSBF20LPT models deliver enhanced power with a heating capacity of 20,000 BTU. The HSBF20LPT focuses on high efficiency and user convenience, featuring an automatic thermostat control to maintain desired temperatures without constant adjustment. Its robust design is perfect for larger areas, ensuring consistent warmth and comfort.

On the other hand, the TSBF20LPT is portable like its 10,000 BTU counterpart but with double the capacity. Its rugged construction and portability make it ideal for both indoor and outdoor use. The unit's reliability in diverse conditions is coupled with an ease of operation, providing warmth where it's most needed.

All models in this Enerco range prioritize user safety and efficiency. Featuring built-in safety mechanisms such as flame failure protection and tip-over shut-off systems, each heater ensures safe operation. Furthermore, the robust construction and high-quality materials used in these devices promise durability, making them a worthwhile investment for long-term heating needs.

Overall, Enerco's MHBF and TSBF series heaters represent a blend of modern technology, safety features, and user-friendly designs, tailored for a variety of heating applications.
Top Page Image Contents