Stow 8FP manual Assembly INSTRUCTIONS/OPERATIONS

Page 34

ASSEMBLY INSTRUCTIONS/OPERATIONS

FIGURE 35

d)Tap the pulley/bushing assembly against the shaft shoulder with the soft hammer.

e)Tighten the 1/4 inch diameter capscrews progressively with a torque wrench to 95 inch pounds.

Note: this installation procedure is also used when installing replacement pulleys.

8)Belt alignment is checked with the straightedge. Place the straightedge squarely against the driveshaft pulley. Properly aligned pulleys should also place the straightedge squarely against the engine/electric motor pulley. Remove the straightedge and rotate the engine pulley 120 degrees. Recheck the alignment with the straightedge. Repeat the process until the engine/electric motor pulley has been rotated a full 360 degrees. Maximum allowable misalignment is +- 1/32 inch. FIGURE 36.

If engine crankshaft/electric motor pulley alignment needs to be adjusted, proceed as follows:

a)Using the 7/16 inch wrench, remove the two 1/4 inch diameter capscrews from the engine pulley bushing.

b)Insert the capscrews into the tapped holes in the bushing flange. Tighten progressively until the bushing disengages from the pulley.

c)Insert the 1/4 inch diameter capscrews into the tapped holes in the pulley. Tighten progressively until the bushing applies tension to the pulley.

d)Using the straightedge for reference alignment purposes, tap the engine/electric motor pulley/bushing into proper position.

e)Tighten the 1/4-inch diameter capscrews progressively with the torque wrench to 95 inch pounds. FIGURE 37.

FIGURE 36

f)Recheck alignment as outlined per the beginning of Step 8.

9)Apply increased belt tension by progressively tightening the take-up capscrews against the engine crankcase/electric motor thrust plate.

a)Recheck V-belt alignment.

b)Check belt tension with the spring scale or belt tension tool midway between the engine/electric motor and driveshaft pulleys. Belt deflection should measure approximately 3/16 inch at 3-7/8 to 5-1/2 pounds force. FIGURE 38.

c)If belt tension and alignment is within specifications, torque the engine/electric motor attachment capscrews to 20 ft lbs (27 Nm.)

d)Recheck V-belt tension and alignment.

10)Install the belt guard to the main frame. Install the flat washers and self-locking hexagon nuts. Torque the nuts to 35 ft lbs (47 Nm.). Determine that all safety related decals affixed to the belt guard are fully readable. If any decal is not fully readable, replace with a factory approved, replacement part only.

FIGURE 37

8FP FLOOR PLANER SERIES

OPERATION AND PARTS MANUAL REV #1 (10/27/06)

PAGE 34

 

 

 

Image 34
Contents Electric and Gasoline Floor Planers Model 8FP Series Page Table of Contents Table of Contents Page Fax 10% Web OrderedVia Stow Construction EquipmentPage Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Application All Models Removing the Floor Planer from the PalletFilling the 8FP/G Series Engine Fuel Tank Theory of Operation Flail Design and ApplicationStar Flail Beam FlailPentagonal Flail Milling FlailSpacer Washers Function of Spacer WashersProblems encountered by uneven component wear Assembly INSTRUCTIONS/OPERATIONS Flail Drum Design and ApplicationInstalling Flails on the TWO Section Drum General Notes Regarding Flail DrumsNormal installation procedure for milling flails General Notes Regarding the Installation of Flails Installing a Loaded Drum on the DriveshaftTransporting the Floor Planer Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Operating the Floor Planer on the JOB Site Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Stopping the 8FP/G Series Gasoline Powered Floor Planer Stopping the 8FP/E Series Electrically Powered Floor PlanerPreventative Maintenance Check LIST. Application All Models Observe all applicable safety precautions for the solvent Installing a Replacement V-BELT or Pulley Application As SpecifiedAssembly INSTRUCTIONS/OPERATIONS Application All Models Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Parts Required Each, container of dry film lubricant Aligning the Caster Wheels Checking Driveshaft RUN OUT Page Engine Service MAINTENANCE/SERVICEApplication 8FP/G Series Floor Planer Troubleshooting Accelerated Bearing Wear AND/OR Failure Accelerated V-BELT WearUneven Cutting Action Storage StorageFrame GeneralExplanation of Code in Remarks Column Items Found In the Remarks ColumnGX160KQXC9 Qty DescriptionMain Frame Assembly Main Frame AssyTUBE, Vacuum Main Frame Assy Part Name QTYFRAME, Main Axle MountDriveshaft Assembly Driveshaft AssySHEAVE, Driveshaft Driveshaft Assy Part Name QTY. RemarksRING, Retaining External KEY, SpecialRear Frame Assembly Rear Frame AssyBUSHING, Connex Rear Frame Assy Part Name QTY RemarksPIN, Roll 3/16 X 1 Plated SHAFT, Hinge PlatedOperator Handle Assembly Gasoline Operator Handle Assy GasolineSWITCH, SHUT-OFF BOOT, RubberBARREL, Adjusting TAP, 22-18 Guage WireGasoline Engine Assembly Gasoline Engine AssyDrive Pulley Part Name QTY. RemarksFRAME, Main GX160KQXC9 ENGINE, Honda 5.5HP BUSHING, Center HUBOperator Handle Assembly Electric Operator Handle AssyHOUSING, Switch Height Adjustment ScrewAdjusting Tube Switch Mount SWITCH, ON/OFFElectric Motor Assembly Electric Motor AssyRELIEF, Strain MOTOR, Electric 5HPMotor Plate NUT, BulklheadONE Section Drum Assembly ONE Section Drum AssyFlail Drum ROD ONE Section Drum Assy Part NameFlail Drum END CAP WASHER, Lock 1/4TWO Section Drum Assembly TWO Section Drum AssyTWO Section Drum Assy Part Name Flail Drum 2 SectionFLAILS, Spacers and Washers Assembly Flails & Spacer Washers AssySpacer Washer FLAILS, Spacers and Washers Assy Part Name QTYStar Flail Beam FlailDecals Decal Depth Control Dclsdp Decal Stow Large Decals Part Name QTY RemarksDecal Warning Flails Decalwarning GuardsPayment Terms Special Expediting ServicePRICING, Rebates Specifications Freight PolicyPage Heres HOW to GET Help