Jet Tools JJ-6CSDX, JJ-6CSX operating instructions

Page 5

20.Keep visitors a safe distance from the work area. Keep children away.

21.Make your workshop child proof with padlocks, master switches or by removing starter keys.

22.Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury.

23.Maintain a balanced stance at all times so that you do not fall or lean against the spindle or other moving parts. Do not overreach or use excessive force to perform any machine operation.

24.Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and safer.

25.Use recommended accessories; improper accessories may be hazardous.

26.Maintain tools with care. Keep drill bits sharp and clean for the best and safest performance. Follow instructions for lubricating and changing accessories.

27.Make sure the work piece is securely attached or clamped to the table. Never use your hand to hold the work piece.

28.Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do not use your hands.

29.Do not stand on the machine. Serious injury could occur if the machine tips over.

30.Never leave the machine running unattended. Turn the power off and do not leave the machine until it comes to a complete stop.

31.Before turning on machine, remove all extra equipment such as keys, wrenches, scrap, stock, and cleaning rags away from the machine.

32.Always use a hold-down or push block when surfacing stock less than 12" inches long, or 3 inches wide, or 3 inches thick.

33.Do not perform jointing operations on material shorter than 8", narrower than 3/4" or less than 1/4" thick.

34.The hands must never be closer than 3 inches to the cutterhead (see Figure).

35.Never apply pressure to stock directly over the cutterhead. This may result in the stock tipping into the cutterhead along with the operator's fingers. Position hands away from extreme ends of stock, and push through with a smooth, even motion. Never back workpiece toward the infeed table.

36.Do not make cuts deeper than 1/2" when rabbeting. On other cuts such as edging, surfacing, etc., depth of cut should not be over 1/8" to avoid overloading the machine and to minimize chance of kickback.

37.To avoid kickback, the grain must run in the same direction you are cutting. Before attempting to joint, or plane, each work piece must be carefully examined for stock condition and grain orientation.

38.When working with a swirl grain wood or burls, making it necessary to plane against the grain, use a lesser depth of cut and a slow rate of feed.

5

Image 5
Contents Woodworking Jointer More Information WMH Tool Group Warranty WarrantyTable of Contents Page Page On-Off Switch Padlock JJ-6CSX JJ-6CSDX Introduction SpecificationsUnpacking Shipping ContentsInstalling Bed to Stand AssemblyUnpacking and Cleanup Installing the Drive Belt Installing Fence to BedInstalling Cutterhead Guard Installing Belt GuardInstalling Access Cover Installing Dust ChuteVolt Operation ElectricalGrounding Instructions Drive Belt Tension AdjustmentsFence Movement To tilt fence backward90º Fence Adjustment Fence Stop AdjustmentsInfeed Table Depth Stop Gib AdjustmentSetting Cutterhead Knives JJ-6CSX Replacing Knives JJ-6CSX Outfeed Table Adjustment Setting Cutterhead Knives JJ-6CSDX Replacing Knives JJ-6CSDX Setting Knives for Rabbeting and NicksDetermining Correct Table Height Operation Operating ControlsEdge Jointing Hand PlacementSurfacing Jointing Warped Surfaces RabbetingJointing Short or Thin Work Beveling MaintenanceDirection of Grain Blade CareCutterhead Removal Lubrication Troubleshooting Operating ProblemsTroubleshooting Mechanical and Electrical Problems Parts Optional AccessoriesOrdering Replacement Parts Index No. Part No Description Size Qty Fence Parts All ModelsFence Assembly All Models TS-0267041 Stand Parts All ModelsStand Parts and Assembly All Models JJ6CSDX-403 Bed Parts All ModelsTS-0207021 Socket Head Cap Screw JJ-6CSDX Cutterhead Parts and Assembly JJ-6CSX JJ6CSDX-101 Cutterhead Parts and Assembly JJ-6CSDXWiring Diagram All Models Page WMH Tool Group