Powermatic 60HH, 60C operating instructions Operating Controls, Start/Stop

Page 21

Operating Controls

Start/Stop

Power Indicator Light – The start switch has a power indicator lamp which is on whenever there is power connected to the Jointer, not just when the Jointer is running. Do not assume that no light means there is no power to the machine. If the bulb is bad, there will be no indication. Always check before use.

Do not rely that no light
means no power to the machine. Always
check for power first. Failure to comply may
cause serious injury!
Refer to Figure 30:
Start – Press the green start switch.
When power is connected to the machine, the
green light is always on regardless of whether
the Jointer is running or not.
Stop – Press the red switch to stop.
Reset – In the event that the Jointer stops	Figure 30
without pressing the stop button, as the result of	Figure 30
a tripped fuse or circuit breaker, etc.:
Press red button to reset main switch.
Press the green button to restart the machine.
Safety Key
The start/stop switch on the Jointer comes
equipped with a magnetic safety key. When in
place on the switch as shown in Figure 30, the
magnetic safety key trips a relay which will allow
the machine to start and stop when the
respective switches are pressed. Being
magnetic, the lock can be removed to make the
machine inoperable and can be hidden for safe
storage by attaching it to another magnetic
surface.
When using the Jointer, place the key on the
switch cover lining up the arrow on the key with
the REMOVE arrow on the cover. Then rotate
the key so that the arrow lines up with the LOCK
arrow on the cover. This will prevent the safety
key from coming loose from vibration when the
machine is in use.

21

Image 21

Contents Part No. M-1610084 PowermaticWarranty Period Warranty and ServiceTable of Contents Page Page Introduction Specifications 3HP 3PH 230/460V prewired60C Features and Terminology 60C and 60HH Jointers Unpacking Contents of the Shipping ContainerTools required for assembly AssemblyAssembling Jointer to Stand Cutterhead GuardInstalling Drive Belt Aligning PulleysRemoving Guard Installing Switch Arm Installing Belt Guard and DoorInstalling Dust Chute Hose and clamp not providedKnife Gauge Assembly model 60C only Installing Fence HandwheelElectrical Connections Storing the Push BlocksGrounding Instructions Installing and Adjusting Knives AdjustmentsExtension Cords Straight cutterhead onlyStraight cutterhead only Helical Cutterhead Only Replacing and Rotating Knife InsertsIf table will still not line up Leveling Tables Setting Outfeed Table Adjusting Depth of Cut Rapid Adjust Fine AdjustExamples of incorrect settings Spring CuttingFence Movement See Figure Fence StopsDegree stop Degree forward stopStart/Stop Operating ControlsBasic Jointer Operation Hand PlacementJointing Short or Thin Work Direction of GrainJointing Warped Surfaces Edge JointingBeveling Taper Cuts Skewing Shear CuttingRabbeting MaintenanceSharpening Knives model 60C only Cutterhead MaintenanceTable Removal Troubleshooting Mechanical and Electrical Problems TroubleProbable Cause Remedy Trouble Probable Cause Remedy Troubleshooting Operating Problems Straight cutterhead Replace nickedHelical cutterhead Rotate nicked Replacement Parts Parts List Base Assembly 60C and 60HHIndex No. Part No Description Size Qty 6296044 Base Assembly 60C and 60HH Parts List Fence Assembly 60C and 60HH Fence Assembly 60C and 60HH Parts List Straight Cutterhead Assembly 60C only Parts List Helical Cutterhead Assembly 60HH only Parts List Stand Assembly 60C and 60HH PM2000-105 Stand Assembly 60C and 60HH Electrical Connections Single Phase, 230 Volt Electrical Connections 3 Phase, 230 Volt Electrical Connections 3 Phase, 460 Volt New Sanford Rd LaVergne, TN Phone

Related manuals

Manual 44 pages 36.77 Kb