Powermatic 60HH, 60C Assembly, Assembling Jointer to Stand, Cutterhead Guard, Refer to Figure

Page 9

Assembly

Exposed metal surfaces, such as the table and fence, have been given a protective coating at the factory. This coating should be removed with a soft cloth and solvent (such as mineral spirits) once the machine has been assembled. Do not use an abrasive pad as it may scratch the exposed surfaces.

NOTE: If any procedure described herein needs further clarification, consult the assembly drawings at the back of this manual.

Tools required for assembly:

3mm, 4mm and 6mm hex (Allen) wrenches 17mm, 14mm, (two)12mm open-end wrenches screwdriver

Assembling Jointer to Stand

Refer to Figure 6.

1.Locate the stand on a level floor. If desired, the stand can be secured to the floor using two anchor bolts (not provided) through the holes inside the bottom of the stand. If using an optional mobile base, be sure to lock the wheels before assembling, operating or adjusting the jointer.

The jointer is very heavy.

Exercise proper caution when lifting it.

2.Use a hoist or forklift with straps, to lift the jointer onto the stand. (The front of the jointer should face the same direction as curved front of the stand.)

3.Shift the jointer atop the stand until the 3- hole pattern aligns in jointer base and stand.

4.Secure jointer base to stand with three 3/8”- 16 x 2-3/8” carriage bolts (AA), six 3/8” flat washers (BB), three 3/8” lock washers (CC) and three 3/8” hex nuts (DD). (Note: On the

left hand hole, it may be easier to insert the

carriage bolt from beneath as shown.) OnlyFigure 6 finger tighten bolts until all three are

properly inserted; then fully tighten the hex nuts with a 14mm wrench and a 17mm wrench on the heads of the screws.

Cutterhead Guard

Place the post of the cutterhead guard (J, Figure

6)into the hole on the rabbeting ledge as shown. (Always use caution when working near the cutterhead knives!) Rotate the set screw with a 4mm hex wrench until it tightens into the groove on the cutterhead guard post.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Part No. M-1610084 PowermaticWarranty Period Warranty and ServiceTable of Contents Page Page Introduction Specifications 3HP 3PH 230/460V prewired60C Features and Terminology 60C and 60HH Jointers Unpacking Contents of the Shipping ContainerTools required for assembly AssemblyAssembling Jointer to Stand Cutterhead GuardInstalling Drive Belt Aligning PulleysRemoving Guard Installing Switch Arm Installing Belt Guard and DoorInstalling Dust Chute Hose and clamp not providedKnife Gauge Assembly model 60C only Installing Fence HandwheelElectrical Connections Storing the Push BlocksGrounding Instructions Installing and Adjusting Knives AdjustmentsExtension Cords Straight cutterhead onlyStraight cutterhead only Helical Cutterhead Only Replacing and Rotating Knife InsertsIf table will still not line up Leveling TablesSetting Outfeed Table Adjusting Depth of CutRapid Adjust Fine AdjustExamples of incorrect settings Spring CuttingFence Movement See Figure Fence StopsDegree stop Degree forward stopStart/Stop Operating ControlsBasic Jointer Operation Hand PlacementJointing Short or Thin Work Direction of GrainJointing Warped Surfaces Edge JointingBeveling Taper Cuts Skewing Shear CuttingRabbeting MaintenanceSharpening Knives model 60C only Cutterhead MaintenanceTable Removal Troubleshooting Mechanical and Electrical Problems TroubleProbable Cause Remedy Trouble Probable Cause Remedy Troubleshooting Operating Problems Straight cutterhead Replace nickedHelical cutterhead Rotate nicked Replacement Parts Parts List Base Assembly 60C and 60HHIndex No. Part No Description Size Qty 6296044 Base Assembly 60C and 60HH Parts List Fence Assembly 60C and 60HH Fence Assembly 60C and 60HH Parts List Straight Cutterhead Assembly 60C only Parts List Helical Cutterhead Assembly 60HH only Parts List Stand Assembly 60C and 60HH PM2000-105 Stand Assembly 60C and 60HH Electrical Connections Single Phase, 230 Volt Electrical Connections 3 Phase, 230 Volt Electrical Connections 3 Phase, 460 Volt New Sanford Rd LaVergne, TN Phone
Related manuals
Manual 44 pages 36.77 Kb

60C, 60HH specifications

The Powermatic 60C and 60HH are two exceptional entries in the world of woodworking machinery, specifically designed for woodworkers who demand precision and efficiency in their operations. Both models embody Powermatic's commitment to innovation and performance, catering to the needs of professionals and serious hobbyists alike.

One of the standout features of the Powermatic 60C is its advanced digital readout (DRO) system. This technology provides users with accurate measurements and easy adjustments, ensuring that every cut is made with precision. The system helps eliminate guesswork, allowing woodworkers to focus on their craft without worrying about the accuracy of their settings. The 60C also features a powerful 1.75 HP motor, which is capable of handling even the toughest hardwoods with ease.

On the other hand, the Powermatic 60HH boasts the Helical Cutterhead technology, which offers a significant upgrade over traditional straight knives. The helical design consists of multiple cutting edges that provide a smoother cut and reduce tear-out, resulting in a superior finish. This is especially beneficial when working with figured woods or delicate materials. The 60HH also features a 3 HP motor, providing ample power for demanding applications and ensuring consistent performance even under heavy loads.

Both models are equipped with a rigid and robust cast-iron construction, ensuring stability and reducing vibration during operation. This design enhances the durability of the machines and extends their lifespan, making them a worthwhile investment for any serious woodshop.

The jointer beds are precision-ground and provide excellent support for long workpieces, while the fence is easily adjustable and provides accurate guidance for various operations, such as jointing and planing. The intuitive controls make it easy for users to switch between different functions and settings, enhancing workflow efficiency.

In terms of mobility, both the 60C and 60HH come with sturdy, adjustable legs and can be fitted with mobility kits that allow for easy movement around the workshop. This flexibility is a significant advantage for woodworkers who need to optimize their workspace.

In summary, the Powermatic 60C and 60HH represent the pinnacle of jointer and planer technology. With their innovative features, powerful motors, and user-friendly designs, these machines deliver unparalleled performance, making them invaluable assets in any woodworking shop. Whether you prioritize precise adjustments with the 60C or superior cutting capabilities with the 60HH, both models stand ready to elevate your woodworking projects to new heights.
Top Page Image Contents