Powermatic 60HH, 60C operating instructions Table Removal

Page 27

9.Lift cutterhead straight up from base.

10.Remove pulley and both bearing housings.

IMPORTANT: The bearings are press fitted; if they need replacement, this should be done by qualified service personnel only.

To re-install cutterhead, reverse the above procedure. Before re-installing, make sure the machine's curved seats of the base casting are free of dirt, dust or grease, to help ensure a tight fit.

NOTE: Whenever the cutterhead is re-installed on the jointer, the tables must be leveled in relationship to it. See the appropriate sections in this manual.

You may wish to keep an extra cutterhead on hand to maintain shop productivity.

Table Removal

Should the table(s) ever need to be removed, such as for gib maintenance or replacement, proceed as follows:

1.Disconnect jointer from power source.

2.Remove fence assembly except for the support casting.

3.Remove cutter guard.

4.Lower infeed and outfeed tables and remove cutterhead.

5.Loosen the gib set screws and table lock screws.

After gib screws are loosened, table could suddenly slide down.

6.Remove infeed or outfeed table by sliding upward.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Part No. M-1610084 PowermaticWarranty Period Warranty and ServiceTable of Contents Page Page Introduction Specifications 3HP 3PH 230/460V prewired60C Features and Terminology 60C and 60HH Jointers Unpacking Contents of the Shipping ContainerCutterhead Guard AssemblyTools required for assembly Assembling Jointer to StandInstalling Drive Belt Aligning PulleysRemoving Guard Hose and clamp not provided Installing Belt Guard and DoorInstalling Switch Arm Installing Dust ChuteStoring the Push Blocks Installing Fence HandwheelKnife Gauge Assembly model 60C only Electrical ConnectionsGrounding Instructions Straight cutterhead only AdjustmentsInstalling and Adjusting Knives Extension CordsStraight cutterhead only Helical Cutterhead Only Replacing and Rotating Knife InsertsIf table will still not line up Leveling TablesFine Adjust Adjusting Depth of CutSetting Outfeed Table Rapid AdjustExamples of incorrect settings Spring CuttingFence Movement Degree forward stop Fence StopsSee Figure Degree stopStart/Stop Operating ControlsDirection of Grain Hand PlacementBasic Jointer Operation Jointing Short or Thin WorkJointing Warped Surfaces Edge JointingBeveling Taper Cuts Skewing Shear CuttingRabbeting MaintenanceSharpening Knives model 60C only Cutterhead MaintenanceTable Removal Troubleshooting Mechanical and Electrical Problems TroubleProbable Cause Remedy Trouble Probable Cause Remedy Troubleshooting Operating Problems Straight cutterhead Replace nickedHelical cutterhead Rotate nicked Replacement Parts Parts List Base Assembly 60C and 60HHIndex No. Part No Description Size Qty 6296044 Base Assembly 60C and 60HH Parts List Fence Assembly 60C and 60HH Fence Assembly 60C and 60HH Parts List Straight Cutterhead Assembly 60C only Parts List Helical Cutterhead Assembly 60HH only Parts List Stand Assembly 60C and 60HH PM2000-105 Stand Assembly 60C and 60HH Electrical Connections Single Phase, 230 Volt Electrical Connections 3 Phase, 230 Volt Electrical Connections 3 Phase, 460 Volt New Sanford Rd LaVergne, TN Phone
Related manuals
Manual 44 pages 36.77 Kb

60C, 60HH specifications

The Powermatic 60C and 60HH are two exceptional entries in the world of woodworking machinery, specifically designed for woodworkers who demand precision and efficiency in their operations. Both models embody Powermatic's commitment to innovation and performance, catering to the needs of professionals and serious hobbyists alike.

One of the standout features of the Powermatic 60C is its advanced digital readout (DRO) system. This technology provides users with accurate measurements and easy adjustments, ensuring that every cut is made with precision. The system helps eliminate guesswork, allowing woodworkers to focus on their craft without worrying about the accuracy of their settings. The 60C also features a powerful 1.75 HP motor, which is capable of handling even the toughest hardwoods with ease.

On the other hand, the Powermatic 60HH boasts the Helical Cutterhead technology, which offers a significant upgrade over traditional straight knives. The helical design consists of multiple cutting edges that provide a smoother cut and reduce tear-out, resulting in a superior finish. This is especially beneficial when working with figured woods or delicate materials. The 60HH also features a 3 HP motor, providing ample power for demanding applications and ensuring consistent performance even under heavy loads.

Both models are equipped with a rigid and robust cast-iron construction, ensuring stability and reducing vibration during operation. This design enhances the durability of the machines and extends their lifespan, making them a worthwhile investment for any serious woodshop.

The jointer beds are precision-ground and provide excellent support for long workpieces, while the fence is easily adjustable and provides accurate guidance for various operations, such as jointing and planing. The intuitive controls make it easy for users to switch between different functions and settings, enhancing workflow efficiency.

In terms of mobility, both the 60C and 60HH come with sturdy, adjustable legs and can be fitted with mobility kits that allow for easy movement around the workshop. This flexibility is a significant advantage for woodworkers who need to optimize their workspace.

In summary, the Powermatic 60C and 60HH represent the pinnacle of jointer and planer technology. With their innovative features, powerful motors, and user-friendly designs, these machines deliver unparalleled performance, making them invaluable assets in any woodworking shop. Whether you prioritize precise adjustments with the 60C or superior cutting capabilities with the 60HH, both models stand ready to elevate your woodworking projects to new heights.
Top Page Image Contents