Powermatic 60C, 60HH operating instructions

Page 4

1.Read and understand the entire owner’s manual before attempting assembly or operation.

2.Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3.Replace the warning labels if they become obscured or removed.

4.This jointer is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a jointer, do not use until proper training and knowledge have been obtained.

5.Do not use this jointer for other than its intended use. If used for other purposes, Powermatic disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6.Always wear approved safety glasses/face shields while using this jointer. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

7.Before operating this jointer, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.

8.Wear ear protectors (plugs or muffs) during extended periods of operation.

9.Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•Lead from lead based paint.

•Crystalline silica from bricks, cement and other masonry products.

•Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.

10.Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

11.Make certain the switch is in the OFF position before connecting the machine to the power supply.

12.Make certain the machine is properly grounded.

13.Make all machine adjustments or maintenance with the machine unplugged from the power source. A machine under repair should be RED TAGGED to show that it should not be used until maintenance is complete.

14.Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

15.Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately after maintenance is complete.

16.Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

17.Provide for adequate space surrounding work area and non-glare, overhead lighting.

18.Keep the floor around the machine clean and free of scrap material, oil and grease.

19.Keep visitors a safe distance from the work area. Keep children away.

20.Make your workshop child proof with padlocks, master switches or by removing starter keys.

21.Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Powermatic Part No. M-1610084Warranty and Service Warranty PeriodTable of Contents Page Page 3HP 3PH 230/460V prewired Introduction Specifications60C Features and Terminology 60C and 60HH Jointers Contents of the Shipping Container UnpackingAssembly Tools required for assemblyAssembling Jointer to Stand Cutterhead GuardAligning Pulleys Installing Drive BeltRemoving Guard Installing Belt Guard and Door Installing Switch ArmInstalling Dust Chute Hose and clamp not providedInstalling Fence Handwheel Knife Gauge Assembly model 60C onlyElectrical Connections Storing the Push BlocksGrounding Instructions Adjustments Installing and Adjusting KnivesExtension Cords Straight cutterhead onlyStraight cutterhead only Replacing and Rotating Knife Inserts Helical Cutterhead OnlyLeveling Tables If table will still not line upAdjusting Depth of Cut Setting Outfeed TableRapid Adjust Fine AdjustSpring Cutting Examples of incorrect settingsFence Movement Fence Stops See FigureDegree stop Degree forward stopOperating Controls Start/StopHand Placement Basic Jointer OperationJointing Short or Thin Work Direction of GrainEdge Jointing Jointing Warped SurfacesBeveling Skewing Shear Cutting Taper CutsMaintenance RabbetingCutterhead Maintenance Sharpening Knives model 60C onlyTable Removal Trouble Troubleshooting Mechanical and Electrical ProblemsProbable Cause Remedy Trouble Probable Cause Remedy Straight cutterhead Replace nicked Troubleshooting Operating ProblemsHelical cutterhead Rotate nicked Parts List Base Assembly 60C and 60HH Replacement PartsIndex No. Part No Description Size Qty 6296044 Base Assembly 60C and 60HH Parts List Fence Assembly 60C and 60HH Fence Assembly 60C and 60HH Parts List Straight Cutterhead Assembly 60C only Parts List Helical Cutterhead Assembly 60HH only Parts List Stand Assembly 60C and 60HH PM2000-105 Stand Assembly 60C and 60HH Electrical Connections Single Phase, 230 Volt Electrical Connections 3 Phase, 230 Volt Electrical Connections 3 Phase, 460 Volt New Sanford Rd LaVergne, TN Phone
Related manuals
Manual 44 pages 36.77 Kb

60C, 60HH specifications

The Powermatic 60C and 60HH are two exceptional entries in the world of woodworking machinery, specifically designed for woodworkers who demand precision and efficiency in their operations. Both models embody Powermatic's commitment to innovation and performance, catering to the needs of professionals and serious hobbyists alike.

One of the standout features of the Powermatic 60C is its advanced digital readout (DRO) system. This technology provides users with accurate measurements and easy adjustments, ensuring that every cut is made with precision. The system helps eliminate guesswork, allowing woodworkers to focus on their craft without worrying about the accuracy of their settings. The 60C also features a powerful 1.75 HP motor, which is capable of handling even the toughest hardwoods with ease.

On the other hand, the Powermatic 60HH boasts the Helical Cutterhead technology, which offers a significant upgrade over traditional straight knives. The helical design consists of multiple cutting edges that provide a smoother cut and reduce tear-out, resulting in a superior finish. This is especially beneficial when working with figured woods or delicate materials. The 60HH also features a 3 HP motor, providing ample power for demanding applications and ensuring consistent performance even under heavy loads.

Both models are equipped with a rigid and robust cast-iron construction, ensuring stability and reducing vibration during operation. This design enhances the durability of the machines and extends their lifespan, making them a worthwhile investment for any serious woodshop.

The jointer beds are precision-ground and provide excellent support for long workpieces, while the fence is easily adjustable and provides accurate guidance for various operations, such as jointing and planing. The intuitive controls make it easy for users to switch between different functions and settings, enhancing workflow efficiency.

In terms of mobility, both the 60C and 60HH come with sturdy, adjustable legs and can be fitted with mobility kits that allow for easy movement around the workshop. This flexibility is a significant advantage for woodworkers who need to optimize their workspace.

In summary, the Powermatic 60C and 60HH represent the pinnacle of jointer and planer technology. With their innovative features, powerful motors, and user-friendly designs, these machines deliver unparalleled performance, making them invaluable assets in any woodworking shop. Whether you prioritize precise adjustments with the 60C or superior cutting capabilities with the 60HH, both models stand ready to elevate your woodworking projects to new heights.
Top Page Image Contents