Porter-Cable Your Guide to Porter Cable Manuals and Edge Guide Adjustment
Page 12

ADJUSTING DEPTH OF CUT

DISCONNECT TOOL FROM POWER SOURCE.

1.Loosen base locking screw (Fig. 3) approximately one-quarter turn.

2.Turn depth adjusting wheel (Fig. 3) clockwise, looking at top of wheel, to raise cutter reducing depth of cut or counterclockwise to lower cutter for increasing depth of cut.

3.Tighten base locking screw securely and make a test cut in scrap material and check depth of cut.

4.Repeat steps 1 through 3 until desired depth of cut is achieved.

LOCKING

SCREW SPRING WASHER

DEPTH ADJUSTING

WHEEL

Fig. 3

ADJUSTING SUB-BASE ALIGNMENT

Applications using a templet guide require the bit to be centered within the guide. This, in turn, requires the center hole in the sub-base to be in line with the collet of the motor unit. Your model has an adjustable sub-base which has been aligned at the factory. If the sub-base has been removed and/or readjustment is required, proceed as follows:

DISCONNECT TOOL FROM POWER SOURCE.

1.Install 42054 Templet Guide (available as an accessory) to the subbase and tighten securely.

2.Loosen sub-base mounting screws just enough to allow sub-base to move on base.

3.Install a straight 1/4" diameter bit in collet of motor unit and tighten securely.

4.Assemble motor unit to base, align hole in templet guide with 1/4" diameter bit and adjust depth of cut so that bit extends through templet guide. Tighten motor unit in base.

5.Tighten sub-base mounting screws securely.

73100 EDGE GUIDE KIT

The Model 73100 Edge Guide Kit is available (as an accessory), for use with the Model 310 trimmer. The 73100 is designed for use with non-piloted bits, on curved or straight applications. Non-piloted bits can produce a 90° straight cut, a 10° bevel cut, or a 22° bevel cut. The kit (Fig. 4) contains:

A – Base and roller guide - for flush or bevel trimming

B – Edge guide – for flush trimming

C – Edge guide – for bevel trimming

D – Straight edge guide – for straight trimming

E – Guide setting gauge

F – Mounting screws

G – Wrench

DISCONNECT TOOL FROM POWER SOURCE.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Double Insulated Table of Contents Important Safety InstructionsSafety Guidelines Definitions California PropositionGeneral Safety Rules General Safety Rules Additional Specific Safety Rules Clear the Trimmer BIT Area before starting motorPage Symbol Definition Motor Extension Cord SelectionCarton Contents Functional DescriptionOperation Model 7310 Trimmer Assembly To Install BITTo Remove BIT Adjusting Depth of CUT Adjusting SUB-BASE AlignmentEdge Guide KIT Assembling and Adjusting Base and Roller Guide Flush TrimmingModel 7319 Tilt Base Trimmer Assembly Using Straight Edge GuideBevel Trimming Model 7312 Offset Trimmer Assembly Adjusting TiltAssembling Offset Base to Motor To Install & Remove BIT OperationSUB-BASE Inverted Underscribe 7320 Trimmer Assembly Typical ApplicationsAdjusting BIT Exposure Adjusting Guide PlateUsing Underscribe Trimmer Troubleshooting Guide Maintenance Keep Tool CleanFailure to Start LubricationService AccessoriesReplacement Parts Service and RepairsWarranty PORTER-CABLE Limited ONE Year WarrantyCanadian PORTER-CABLE Delta Service Centers

MODEL 7310 specifications

The Porter-Cable MODEL 7310 is a versatile and user-friendly sander designed to meet the demands of both professional and DIY woodworkers. One of its standout features is its unique sanding system, which utilizes a 3-inch by 21-inch belt for unbeatable efficiency in both large surface areas and intricate detailing. The combination of its powerful motor and adjustable speed settings allows users to customize their sanding experience depending on the task at hand.

One key characteristic of the MODEL 7310 is its ability to deliver a variable speed range, typically ranging from 120 to 400 feet per minute. This flexibility enables users to achieve a smooth finish on various materials, including hardwoods, softwoods, and composites. The sander is equipped with a dust collection system that enhances its usability by minimizing mess. The built-in dust port effectively captures and directs debris away from the work area, ensuring that users can maintain a clean workspace while prolonging the life of the sanding belt.

Another notable feature of the MODEL 7310 is its ergonomic design. The machine includes a cushioned grip that reduces fatigue during prolonged use, allowing for better control and precision. The compact design also makes it lightweight, enhancing maneuverability without sacrificing power. Alongside its comfortable grip, the sander's low profile ensures easy access to tight spaces, such as corners and edges.

Safety is also a priority for Porter-Cable, and the MODEL 7310 is outfitted with important safety features. The sander is designed with a locking mechanism that prevents accidental startup, providing an additional layer of safety for the user. Furthermore, the durable construction of the sander ensures it can withstand the rigors of everyday use, making it a reliable addition to any workshop.

In summary, the Porter-Cable MODEL 7310 stands out in the market due to its high performance, user-friendly features, and robust construction. With its variable speed control, efficient dust collection, ergonomic design, and reliable safety features, it is an excellent choice for anyone seeking a powerful and adaptable sander. Whether you are a seasoned professional or a casual DIY enthusiast, the MODEL 7310 is engineered to deliver exceptional results on any woodworking project.
Top Page Image Contents