Jet Tools JPM-13CS operating instructions Planing procedure, Adjusting chip deflectors for planing

Page 13

7.Insert the block labeled “Feed Roller Planing” into the planer opening.

8.Raise or lower the feed roller until it rests on top of the block end to end. To adjust the feed roller (Fig 12):

Loosen the jam nut on both sides of infeed roller with the wrench provided.

Turn the threaded bushing counter- clockwise to raise roller and clockwise to lower roller.

Raise or lower roller until it contacts the top of the block on both ends of the roller.

Block should slide in and out with a minimum of force.

Tighten jam nuts and re-check.

9.Repeat this process with outfeed roller. Retain the wooden blocks for future use.

Figure 12

10.8Adjusting chip deflectors for planing

Adjust the outfeed chip deflector (as shown in Figure 13) to within 1/4” to 1/8” of planing knives to prevent chips from being pressed into the planed surface of the work piece by the outfeed roller. Note: Adjusting the chip deflector too close to the cutterhead while planing will cause a higher than normal noise level especially when using a dust collector. The use of a dust collection system with the capacity to handle a large volume of material is highly recommended.

Figure 13

The infeed chip deflector (curved piece attached to the top cover with three screws and wing nuts) must be adjusted as close to the cutterhead as the

adjustment allows without contacting the cutterhead and knives.

11.0Planing procedure

Never stand directly in front of or behind machine while planing or molding. Always stand to one side. Failure to comply may cause serious injury from kickback.

Never attempt to plane a workpiece shorter than 14” or thinner than 1/2”. Failure to comply may cause serious injury.

Never plane more than 1/8” on stock narrower than 5-1/2” and 1/16” on stock 5-1/2” and wider in one pass. This will cause stress on machine, lead to premature wear, and may damage knives and/or cutterhead.

The use of a dust collection system is highly recommended. If a dust collection system is not used, remove hose adaptor from dust hood to prevent wood chips collecting in dust hood and backing up into machine.

The JPM-13CS is supplied with planing blades mounted in the cutterhead. Planing can be done at 10 FPM for an improved surface finish or 20 FPM for faster planing. Work pieces longer than 24” should be supported with infeed and outfeed rollers.

1.Adjust table height to produce desired depth of cut.

2.Start machine.

3.Stand to one side and grasp work piece in the center.

4.Gently slide work piece into infeed side of planer/molder until infeed roller begins to advance the work piece.

5.Let go of the work piece and allow the feed rollers to advance the work piece.

6.Catch the work piece as it comes out the outfeed side of the planer/molder.

11.1Dealing with warped wood

Warp is caused by different grain directions in a piece of wood drying at different rates during the drying process.

Wood warped across the width - Cupped wood is planed flat on one side first, then planed flat on the other. Ripping the board down the middle will avoid huge amounts of waste in planing to thickness.

13

Image 13
Contents Part No. M-708524 Planer/MolderWarranty Period Warranty and ServiceTable of contents Volts Total Length of Cord in Feet Safety warningsAbout this manual Grounding instructions Electrical connections115 Volt operation 230 Volt operationOn-Off Switch Padlock JPM-13CS SpecificationsGlossary Adjustments Planing Setup and assemblyKnife adjustment Feed rate adjustmentAdjusting V-Belt Tension Adjusting infeed roller and outfeed rollers for planing Knife replacementAdjusting chip deflectors for planing Planing procedureDealing with warped wood Installing molding cutters Molding setup and adjustmentsWood Grain For 2 and under cuttersSetting feed rollers for molding Guide rail placement and attachment Making & installing a bedboardMaking guide rails Setting table height for first pass Molding procedureDisconnect machine from power source unplug MaintenanceBack Relief Molding Tongue and Groove MoldingMechanical and electrical problems Troubleshooting the JPM-13CSTrouble Probable Cause RemedyPerformance problems Replacement Parts Table and Base Assembly Exploded View Index No Description Size Qty Table and Base Assembly Parts ListCutterhead and Roller Assembly Parts List PGE-B19C Gearbox Assembly Parts List MHA-G Stand and Motor Assembly Parts List PJA-C03 Electrical Connections Page New Sanford Road LaVergne, Tennessee Phone