Stanley Black & Decker MBX15 user manual LOW-TEMPERATURE WARM-UP Procedure, Securing the Tool

Page 9

PRE-OPERATION

Grease Will

Fill This

Space

Piston not against tool bit leaving space between the piston and bit.

Tool Stop

Lower Bushing

Tool Bit

LOW-TEMPERATURE WARM-UP

PROCEDURE

1.

After starting the excavator, warm-up the hydraulic

 

system at engine idle until hydraulic lines are warm

 

to the touch.

2.

With the excavator at idle and the breaker suspend-

 

ed in the air or with minimal down pressure, turn on

 

the breaker to gradually warm up its internal com-

 

ponents.

3.

When the hydraulic system and breaker are warm,

Figure 2.

SECURING THE TOOL

1.Lay the breaker in a horizontal position to install the tool bit. Remove the rubber plug (item 35) and the retainer pin (item 28), see Figure 3 below.

Figure 3.

When installing the tool retainer pin (item 28) make sure the rubber plug (item 35) is fully seated. The rubber plug MUST be installed BELOW FLUSH to properly secure the pin.

2.Using a punch and hammer, drive out the tool re- tainer pins (item 29).

WARNING

Flying debris may be caused by striking the rod pins

with a punch or hammer.

Wear eye protection when installing or removing the

rod pins.

Failure to wear eye protection may result in eye

injury.

proceed with operation. See the OPERATION sec-

tion of this manual.

LONG TERM STORAGE

Use the following procedure if storage of the break- er is expected to be more than 6 months.

IMPORTANT: The piston protrudes out the bottom of the cylinder when not in use, although it is inside the lower body it will still be exposed to the elements and will rust damaging internal components when it is put back into service.

Remove the tool bit and discharge the nitrogen gas from the upper accumulator. Use the tool bit to push the pis- ton inside the cylinder where it will be protected from the elements. Grease the lower end of the exposed piston thoroughly. Also thoroughly coat the tool bit, tool stop, retaining pins, and lower bushing with grease.

If hoses are attached to the breaker, install plugs on the hose ends. If hoses are removed from the breaker, install plugs on the hose ends and install plugs in the breaker “IN” and “OUT” ports.

Store breaker in a dry area under cover if possible. It is best to store the breaker in an area that has a consistent temperature to help avoid water condensation causing rust. Store the breaker in a vertical position. Do not store the breaker horizontally for extended periods.

If the breaker has been laid horizontally for more than 6 months, check and/or replace all seals. Check for corro- sion of bolts before operation.

3.Grease the top area of the tool bit as shown on the previous page.

4.Install the tool bit making sure the notches are aligned with the lower body tool retainer pin holes.

5.Install the tool retainer pins, retainer pin and rubber plug. See “Important” Figure 3.

MBX15 User Manual ◄ 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents MBX15 MBX15Read Wear Eye Manual Protection Hearing Breathing Table of Contents General Safety Precautions Safety PrecautionsSafety Precautions Local Safety Regulations Safety SymbolsMBX15 Tool DecalsPRE-INSTALLATION Instructions PRE-OPERATIONPreparation for Operation LOW-TEMPERATURE WARM-UP Procedure Securing the ToolLong Term Storage Preparation for USE OperationPositioning the Excavator Positioning the Breaker Tool on the Work MaterialBreaker Binding BreakingBlank Firing Underwater USE Underwater USEPeriodic Maintenance Checks Each DAYTool Stop & Lower Bushing WORN-OUT Front Bushings or Retainer Pins Tool Failure not Covered Under WarrantyProper USE & Care of Tool Bits Blank Firing or Free RunningCorrosion PryingInternal Material Flaw Tool Failure Covered Under WarrantyMoil ChiselBlunt Problem Cause Solution TroubleshootingCharging the Main Accumulator When disengaging the tester a POP of nitrogen is normalRecommended Torque Values Recommended Tie Rod Torque ProcedureFlow Test Procedures Test ProcedureHeat Load Test Accessories SpecificationsMBX15 Power Cell Illustration QTY Description MBX15 Power Cell Parts ListMBX15 Housing Parts Hydraulic Tools Declaration of Conformity

MBX15 specifications

The Stanley Black & Decker MBX15 is a robust and versatile tool designed for professionals and serious DIY enthusiasts alike. Engineered to meet the needs of various applications, this machine stands out in the crowded marketplace of power tools, providing exceptional reliability and performance.

At the heart of the MBX15 is its powerful motor, which delivers impressive torque and speed, enabling users to tackle a wide range of tasks with ease. The efficiency of this motor allows for quick job completion without sacrificing quality. One of the standout features of the MBX15 is its lightweight design, making it easy to handle during extended use. The ergonomically designed handle ensures maximum comfort, reducing fatigue and enhancing user control.

The MBX15 incorporates advanced technologies that set it apart from its competitors. For instance, it features an innovative vibration-dampening system that minimizes user discomfort. This technology is especially beneficial during prolonged operations, allowing for greater precision and fewer errors. Additionally, the tool is equipped with a quick-change system, enabling users to switch attachments seamlessly, thus enhancing productivity.

A distinctive characteristic of the MBX15 is its versatility. It comes with a variety of attachments specifically designed for different applications such as grinding, polishing, and even surface preparation. This multifunctionality makes it an essential addition to any workshop or job site.

The MBX15 also prioritizes safety, incorporating several features to protect users during operation. The integrated safety switch prevents accidental start-ups, and the durable housing safeguards the internal components, ensuring longevity and reliability even in demanding environments.

In terms of design aesthetics, the MBX15 boasts a sleek and modern look, complete with a sturdy build that reflects the quality synonymous with the Stanley Black & Decker brand. This tool not only delivers on performance but also complements the professionalism of its users.

In conclusion, the Stanley Black & Decker MBX15 is a formidable tool equipped with a powerful motor, innovative technologies, and a user-friendly design. Its versatility, coupled with safety features and comfort, makes it an exceptional choice for any project, whether on a professional job site or at home. With its blend of power and efficiency, the MBX15 is truly a reliable partner for all your grinding and surface preparation needs.
Top Page Image Contents