Miller Electric ICE-27C, 375 manual Controls, 60 PSI, Setting Gas/Air Pressure

Page 21

SECTION 5 − OPERATION

5-1. Controls

4

2

3

5

ON

OFF	1
	1	PRESSURE
		PRESSURE
		60 PSI	6

20

16 24

27

				Set To
Setting Gas/Air Pressure				60 PSI (414 kPa)
1	20		5		20
	20		5		20
16		24	Requires	16	24
			Requires	6
			70-150 PSI	6
			70-150 PSI
			(483-1034 kPa)
		27	Supply		27
		27			27

1 Output Control

Use control to set cutting output.

Place control in Gas/Air Set position to safely adjust gas/air pressure. Only gas/air circuit is activated.

If 22-27 amperes of cutting output is used with 115 VAC input power, and the overload protection on the input power circuit fre- quently opens, either reduce the cutting out-

put and/or the cut time or find more adequate power (see Section 4-1).

2Trouble Lights (See Section 6-2)

3Power Light

4Power Switch

Setting Gas/Air Pressure

5Air Filter/Regulator

6Pressure Adjustment Knob

Place Output control in Gas/Air position and turn on gas/air supply. Lift knob and turn to adjust pressure. Push knob down to lock in setting.

Place Output control in desired cutting output.

.At ambient temperatures below −55 C (235 F), readjustment of gas/air pressure regulator may be necessary.

Ref. 200 808 / Ref. 802 784

OM-2229 Page 17

Image 21

Contents OM-2229200 879N ProcessesDescription From Miller to You Table of Contents Standards DirectivesMarks a special safety message Symbol UsagePlasma Arc Cutting Hazards Cutting can cause fire or explosionFlying Sparks can cause injury Exploding Parts can injureARC Rays can burn eyes and skin Noise can damage hearingCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers LE Coupage présente un risque de feu ou d’explosion Signification des symbolesUNE Décharge Électrique peut entraîner la mort Identifie un message de sécurité particulierLE Bruit peut endommager l’ouïe Risque de blessure en casLES Fumées ET LES GAZ peuvent être dangereux LE Plasma D’ARC peut entraîner des blessuresDES Pieces Chaudes peuvent pro- voquer des brûlures graves LES Bouteilles peuvent exploser si elles sont endommagéesDES Organes Mobiles peuvent provoquer des blessures DES Particules Volantes peuvent blesser les yeuxPrincipales normes de sécurité Information sur les champs électromagnétiquesConsignes relatives aux stimulateurs cardiaques 55.1 + + +I1eff I1maxSpecifications For Torch SpecificationsNon-CE Model CE ModelExceeding duty cycle can damage unit and void warranty Torch Dimensions And WeightDuty Cycle And Overheating OverheatingSelecting a Location Connecting Gas/Air Supply Connecting Input Power Connecting Work ClampInstalling Alternative Plug Setting Gas/Air Pressure Controls60 PSI Cutting Speed Trigger Safety LockSparks go thru metal Sequence Of Operation− Maintenance & Troubleshooting Checking Torch Shield Cup Shutdown System Always turn Off power when changing or checking consumablesTorch And Work Cable Connections Torch ConnectionsWork Cable Connections Checking/Replacing Retaining Cup, Tip, And Electrode Turn Off power source before checking torch partsTroubleshooting Power Source Reset unit Go to Section Troubleshooting Torch− Electrical Diagram OM-2229 − Parts List Item Diagram Part Marking Description Quantity Torch, ICE-27C Support ServiceMiller Electric Mfg. Co Owner’s Record