Miller Electric MARK VIII-2 manual Miller Electric Mfg. Co, Transportation Department

Page 44

Owner’s Record

Please complete and retain with your personal records.

Model Name	Serial/Style Number

Purchase Date	(Date which equipment was delivered to original customer.)

Distributor

Address

City

State	Zip

For Service

Contact a DISTRIBUTOR or SERVICE AGENCY near you.

Always provide Model Name and Serial/Style Number.

Contact your Distributor for:	Welding Supplies and Consumables
	Options and Accessories
	Personal Safety Equipment
	Service and Repair
	Replacement Parts
	Training (Schools, Videos, Books)
	Technical Manuals (Servicing Information
	and Parts)
	Circuit Diagrams
	Welding Process Handbooks
	To locate a Distributor or Service Agency visit
	www.millerwelds.com or call 1-800-4-A-Miller

Contact the Delivering Carrier to:	File a claim for loss or damage during
	shipment.
	For assistance in filing or settling claims, contact
	your distributor and/or equipment manufacturer’s
	Transportation Department.
PRINTED IN USA	♥ 2005 Miller Electric Mfg. Co. 1/05

Miller Electric Mfg. Co.

An Illinois Tool Works Company

1635 West Spencer Street

Appleton, WI 54914 USA

International Headquarters−USA

USA Phone: 920-735-4505 Auto-Attended

USA & Canada FAX: 920-735-4134

International FAX: 920-735-4125

European Headquarters −

United Kingdom

Phone: 44 (0) 1204-593493

FAX: 44 (0) 1204-598066

www.MillerWelds.com

Image 44

Contents OM-218 DescriptionFrom Miller to You Table of Contents Page Symbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux LE Soudage peut provoquer un Incendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaques− Specifications SpecificationsVolt-Ampere Curves Amperes Input at Rated Load Output, 60 HzDuty Cycle And Overheating For Each Module And Total SystemFor Main Transformer Overheating− Installation Selecting a Location And Moving Polyweld SystemMovement Location And AirflowDimensions, Weights And Base Mounting Hole Layout DimensionsWeight Selecting And Preparing Weld Output Cables350 ft 400 ft 15m 30m 45 m 60 m 70 m 90 m 105 m 120 m Weld Cable Size150 ft 200 ft 250 ft Connecting Weld Output Cables Connecting To Weld Output TerminalsRead Safety Blocks at start of -6before proceeding Standard Module ConnectionsCommon Work Cable Size Separate Work ConnectionsParallel Module Connections Separate Work Connections Common WorkRemote Amperage Control Receptacle Remote Contactor Control Connections OptionalConnecting Input Power Volts AC Duplex ReceptaclePositioning Jumper Links TE3 TE2Connecting Input Power Welding Power Source Input Power Con- nectionsClose and secure access door on welding power source Disconnect Device Input Power Connec- tionsElectrical Service Guide Time-Delay− Operation ControlsAmperage Adjustment Controls Power Switch Push Buttons And Pilot LightMin 35 a Max 125 a Set Switch Set Desired Maximum Amperage Hz Model Shown− Maintenance & Troubleshooting Routine MaintenanceMonths Overload ProtectionModule Fuse Links F11 And F12 Through F81 And F82 Blank Module PanelControl Fuses F3 And F4 Before inspecting, maintaining, or servicing TroubleshootingTurn Off polyweld system, and disconnect input power OM-218 − Electrical Diagram Circuit Diagram For Polyweld SystemSD-082 527-C Amperage Range Gas Type Polarity − Selecting and Preparing Tungsten ElectrodeSelecting Tungsten Electrode Preparing Tungsten For DC Electrode Negative Dcen Welding Torch Movement During Welding − Guidelines for TIG Welding GtawPositioining The Torch Positioning Torch Tungsten For Various Weld Joints Butt Weld And Stringer Bead Joint Lap Joint Corner Joint− Parts List Main Assembly Section aTP1 Main Assembly Section B CR1 194 Panel, Front Module w/Components -1Item Panel, Front Lower w/Components -1Item Panel, Front Lower w/ComponentsPage Support ServiceYour distributor also gives To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s