Miller Electric and DS-74DX16, DS-74DX12 manual Installing Wire Guide Extension

Page 17

4-4. Installing Wire Guide Extension

		1	Wire Guide Fitting
		2	Bolt
		3	Monocoil Liner
1		4	Wire Guide Extension
		Tighten bolt to secure liner in wire
	4	guide fitting. Do not overtighten bolt
	4	and crush liner.
		and crush liner.
3		Repeat procedure for opposite
2		side.

Tools Needed:

3/8 in

ST-152 383

OM-1500-14 Page 13

Image 17

Contents Processes OM-1500-14 207 499HDescription File MIG GmawFrom Miller to You Table of Contents Options and Accessories Warranty Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesIndique des instructions spécifiques Symboles utilisésUNE Décharge Électrique peut entraîner la mort LE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-1500-14 Specifications − InstallationInstalling Swivel Into Pipe Post − IntroductionInstalling Boom And Reel Support Installing Control Box And Adjusting TiltInstalling Wire Guide Extension Exceed 100 PSI 689 kPa Equipment Connection DiagramShielding gas pressure not to Pin Information Control Box ConnectionsPin Plug Information Wire Type, Size, And Feed Speed Capability Table Removing Safety Collar And Adjusting BoomMotor Speed Wire Type Wire Size Feed Speed Capability Gun Recommendation TableAgainst surface. Tighten knob so wire Installing And Threading Welding WireSlip at the feeder see pressure adjust Ment above. Cut wire off. Close coverWhen DIP switch positions are changed, Setting Internal DIP SwitchesDIP Switch S1 DIP Switch S4 Not For Customer Use Position Settings And Results For DIP Switch S1Power Source Selection Menu Left/Right Select Switch Power Switch− Operation Operational TermsTime sec Jog/Purge SwitchFront Panel Controls Upper Display To set the correct voltage range for a particular powerProgram Push Button Lower Display Setup Push ButtonWelding Sequence Diagram Adjust ControlSequence Push Button Start WeldAuxiliary Menus Wire Feed Speed Units Trigger Hold SetupBurnback Trigger Program SelectFor more information on Sequence Push Button see Section − Setting Sequence ParametersSequence Parameters In a Program Optional Dual Schedule Switch Diagrams − Setting Dual Schedule ParametersError DiagnosticsError Indications There is a two-position DIPDiagnostics For User Defined Options − Maintenance & TroubleshootingRoutine Maintenance MonthsDisconnect power before troubleshooting TroubleshootingTrouble Remedy PullCircuit Diagram − Electrical Diagram204 144-C 10-3 10-2 10-4 29 28 − Parts ListOptional Control Box PLG117 165 Harness Connectors/ReceptaclesBoom Assembly Boom Assembly -1Item Drive Assembly, Wire -1Items 26 Drive Assembly, WirePLG5 Not available unless listed Hardware is commonFraction Metric Drive Roll and Wire Guide KitsRoll Kit RollPage Start Your Professional Welding Career Now Page Support ServiceYour distributor also gives Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s