Miller Electric DS-74DX12, and DS-74DX16 manual Miller Electric Mfg. Co, Transportation Department

Page 52

Owner’s Record

Please complete and retain with your personal records.

Model Name	Serial/Style Number

Purchase Date	(Date which equipment was delivered to original customer.)

Distributor

Address

City

State	Zip

For Service

Contact a DISTRIBUTOR or SERVICE AGENCY near you.

Always provide Model Name and Serial/Style Number.

Contact your Distributor for:	Welding Supplies and Consumables
	Options and Accessories
	Personal Safety Equipment
	Service and Repair
	Replacement Parts
	Training (Schools, Videos, Books)
	Technical Manuals (Servicing Information
	and Parts)
	Circuit Diagrams
	Welding Process Handbooks
	To locate a Distributor or Service Agency visit
	www.millerwelds.com or call 1-800-4-A-Miller

Contact the Delivering Carrier to:	File a claim for loss or damage during
	shipment.
	For assistance in filing or settling claims, contact
	your distributor and/or equipment manufacturer’s
	Transportation Department.
PRINTED IN USA	♥ 2007 Miller Electric Mfg. Co. 2007−01

Miller Electric Mfg. Co.

An Illinois Tool Works Company

1635 West Spencer Street

Appleton, WI 54914 USA

International Headquarters−USA

USA Phone: 920-735-4505 Auto-Attended

USA & Canada FAX: 920-735-4134

International FAX: 920-735-4125

European Headquarters −

United Kingdom

Phone: 44 (0) 1204-593493

FAX: 44 (0) 1204-598066

www.MillerWelds.com

Image 52

Contents OM-1500-14 207 499H ProcessesDescription File MIG GmawFrom Miller to You Table of Contents Options and Accessories Warranty Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésIndique des instructions spécifiques LES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-1500-14 − Installation SpecificationsInstalling Swivel Into Pipe Post − IntroductionInstalling Control Box And Adjusting Tilt Installing Boom And Reel SupportInstalling Wire Guide Extension Shielding gas pressure not to Equipment Connection DiagramExceed 100 PSI 689 kPa Pin Plug Information Control Box ConnectionsPin Information Removing Safety Collar And Adjusting Boom Wire Type, Size, And Feed Speed Capability TableMotor Speed Wire Type Wire Size Feed Speed Capability Gun Recommendation TableInstalling And Threading Welding Wire Against surface. Tighten knob so wireSlip at the feeder see pressure adjust Ment above. Cut wire off. Close coverSetting Internal DIP Switches When DIP switch positions are changed,DIP Switch S1 DIP Switch S4 Not For Customer Use Position Settings And Results For DIP Switch S1Power Source Selection Menu Power Switch Left/Right Select Switch− Operation Operational TermsFront Panel Controls Jog/Purge SwitchTime sec Program Push Button To set the correct voltage range for a particular powerUpper Display Setup Push Button Lower DisplayAdjust Control Welding Sequence DiagramSequence Push Button Start WeldAuxiliary Menus Trigger Hold Setup Wire Feed Speed UnitsBurnback Trigger Program SelectSequence Parameters In a Program − Setting Sequence ParametersFor more information on Sequence Push Button see Section − Setting Dual Schedule Parameters Optional Dual Schedule Switch DiagramsDiagnostics ErrorError Indications There is a two-position DIP− Maintenance & Troubleshooting Diagnostics For User Defined OptionsRoutine Maintenance MonthsTroubleshooting Disconnect power before troubleshootingTrouble Remedy Pull− Electrical Diagram Circuit Diagram204 144-C − Parts List 10-3 10-2 10-4 29 28Optional Control Box Harness Connectors/Receptacles PLG117 165Boom Assembly Boom Assembly -1Item Drive Assembly, Wire Drive Assembly, Wire -1Items 26PLG5 Hardware is common Not available unless listedDrive Roll and Wire Guide Kits Fraction MetricRoll Kit RollPage Start Your Professional Welding Career Now Page Your distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s