Miller Electric Invision 456MP 120 258 550 160 270 649 200 298, 240 336, 106 702 280 367, 180 801

Page 35

Program 9 −− 1/16 .062 Aluminum 4043 −− Argon

IPM	Trim	Peak Amp	Background Amp	Freq.	Pulse Width	Starting Amps

120	0	258	56	40	2.15	550

160	10	270	89	60	2.40	649

200	20	298	115	80	2.60	649

240	30	336	134	106	2.89	702

280	40	367	148	122	3.15	720

320	50	400	157	134	3.35	737

360	60	421	169	144	3.55	748

400	70	440	181	154	3.70	758

440	80	461	192	164	3.90	772

480	90	480	204	174	4.05	787

520	100	498	216	180	4.18	801

Program 10 −− .035 Aluminum 5356 −− Argon

IPM	Trim	Peak Amp	Background Amp	Freq.	Pulse Width	Starting Amps

350	0	200	65	54	1.90	451

400	10	216	72	66	1.95	451

450	20	230	80	78	2.00	451

500	30	242	87	88	2.05	501

550	40	251	94	96	2.10	501

600	50	261	101	104	2.17	501

650	60	272	108	112	2.24	501

700	70	284	117	121	2.32	501

750	80	296	127	130	2.40	550

800	90	301	131	137	2.45	550

850	100	303	134	140	2.48	550

Program 11 −− .047 Aluminum 5356 −− Argon

IPM	Trim	Peak Amp	Background Amp	Freq.	Pulse Width	Starting Amps

200	0	240	47	55	2.10	501

255	10	270	58	80	2.20	600

310	20	301	65	98	2.30	600

365	30	320	72	110	2.40	652

420	40	341	80	120	2.50	652

475	50	350	91	130	2.60	652

530	60	388	101	140	2.70	652

585	70	411	110	153	2.80	702

640	80	421	120	163	2.90	702

695	90	440	131	168	2.95	702

750	100	461	141	170	3.00	702

OM-193 267 Page 31

Image 35

Contents File MIG Gmaw OM-193 267RProcesses DescriptionFrom Miller to You Table of Contents Page HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO- SionLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-193 267 Duty Cycle and Overheating Specifications394 mm Dimensions and WeightCV Mode CC Mode Volt-Ampere CurvesSelecting a Location 350 ft 400 ft Put terminals Weld Output Terminals and Selecting Cable SizesARC Welding can cause Electromagnetic Interference Remote 14 Receptacle Information Connecting Weld Output CablesInput Voltage Electrical Service GuideHz Three Phase Volts AC Duplex Receptacle and Circuit BreakersSelecting Input Voltage = GND/PE Always connect grounding conductor first Connecting Input PowerFor Models With Optional Ground Current Sensor For All ModelsFront Panel Controls Power SwitchMeter Functions Mode Meter Reading At Idle Meter Reading While WeldingExample Displays Controls Turn Output Adjust control to set arc length toSynergic Controls and Overview ExampleStick appears Press Increment or Decrement button until MIG appearsPress Increment or Setup Screens Choosing Adaptive Or Non Adaptive Choosing Pulse Programs and Setting ParametersSetting Arc Length Choosing Pulse ProgramOM-193 267 Overview of Programs Programs 191 698 478 574 369 600 138 449 206 484 125 624 274 512150 652 342 538 170 674 410 562165 631 486 470 320 441 156 345 472 222 371 120 511 288 402145 550 354 430 155 589 420 454122 720 320 400 120 258 550 160 270 649 200 298240 336 106 702 280 367723 180 291 652 220 312 663 260 338705 300 362150 720 687 508 498 463130 684 561 482 140 705 624 496150 800 320 562 451 674 498 705 140 515 741 185 527230 541 132 800 275 552Months Routine MaintenanceDo not remove case when blowing out inside of unit Blowing Out Inside of Unit802 314 / Ref Ref. ST-801 718 / Ref. ST-801 536-A Voltmeter/Ammeter Help Displays Trouble Remedy Error CodesTroubleshooting − Electrical Diagram 193 264-A Circuit Diagram For Welding Power Source 575 Volt Models 206 318-A − Parts List Dia Part Description Quantity Mkgs Optional Support ServiceYour distributor also gives Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact