Miller Electric Invision 456MP 180 291 652 220 312 663 260 338, 705, 300 362, 723, 340 383, 517

Page 36

Program 12 −− .062 Aluminum 5356 −− Argon

IPM	Trim	Peak Amp	Background Amp	Freq.	Pulse Width	Starting Amps

180	0	291	82	50	2.25	652

220	10	312	98	62	2.38	663

260	20	338	120	77	2.55	705

300	30	362	136	90	2.69	723

340	40	383	148	100	2.80	748

380	50	404	160	110	2.91	772

420	60	428	176	122	3.04	783

460	70	451	192	134	3.19	794

500	80	484	207	146	3.34	801

540	90	501	216	156	3.42	801

580	100	517	225	165	3.50	801

Program 13 −− .035 Nickel −− 75 Argon/25 Helium

IPM	Trim	Peak Amp	Background Amp	Freq.	Pulse Width	Starting Amps

120	0	254	37	40	2.85	501

175	10	287	49	54	2.96	501

230	20	312	61	68	3.08	511

285	30	331	72	77	3.20	522

340	40	348	84	89	3.32	532

395	50	360	91	99	3.40	543

450	60	374	98	108	3.48	554

505	70	390	105	117	3.55	564

560	80	404	112	126	3.62	575

615	90	418	120	135	3.69	585

670	100	432	127	144	3.76	596

Program 14 −− .045 Nickel −− 75 Argon/25 Helium

IPM	Trim	Peak Amp	Background Amp	Freq.	Pulse Width	Starting Amps

100	0	289	56	56	3.00	600

150	10	315	75	76	3.22	600

200	20	345	89	100	3.34	600

250	30	364	103	116	3.50	628

300	40	385	117	129	3.62	645

350	50	404	134	142	3.72	660

400	60	423	150	155	3.82	670

450	70	440	164	168	3.92	677

500	80	458	176	180	4.02	688

550	90	475	188	192	4.12	702

600	100	491	197	204	4.20	712

OM-193 267 Page 32

Image 36

Contents OM-193 267R ProcessesDescription File MIG GmawFrom Miller to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortDES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserProposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-193 267 Specifications Duty Cycle and OverheatingDimensions and Weight CV Mode CC ModeVolt-Ampere Curves 394 mmSelecting a Location Weld Output Terminals and Selecting Cable Sizes ARC Welding can cause Electromagnetic Interference350 ft 400 ft Put terminals Connecting Weld Output Cables Remote 14 Receptacle InformationElectrical Service Guide Hz Three PhaseVolts AC Duplex Receptacle and Circuit Breakers Input VoltageSelecting Input Voltage Connecting Input Power For Models With Optional Ground Current SensorFor All Models = GND/PE Always connect grounding conductor firstPower Switch Front Panel ControlsMode Meter Reading At Idle Meter Reading While Welding Meter FunctionsExample Displays Turn Output Adjust control to set arc length to Synergic Controls and OverviewExample ControlsPress Increment or Decrement button until MIG appears Press Increment orStick appears Setup Screens Choosing Pulse Programs and Setting Parameters Setting Arc LengthChoosing Pulse Program Choosing Adaptive Or Non AdaptiveOM-193 267 Overview of Programs Programs 369 600 138 449 206 484 125 624 274 512 150 652 342 538170 674 410 562 191 698 478 574320 441 156 345 472 222 371 120 511 288 402 145 550 354 430155 589 420 454 165 631 486 470120 258 550 160 270 649 200 298 240 336106 702 280 367 122 720 320 400180 291 652 220 312 663 260 338 705300 362 723498 463 130 684 561 482140 705 624 496 150 720 687 508451 674 498 705 140 515 741 185 527 230 541132 800 275 552 150 800 320 562Routine Maintenance Do not remove case when blowing out inside of unitBlowing Out Inside of Unit Months802 314 / Ref Ref. ST-801 718 / Ref. ST-801 536-A Voltmeter/Ammeter Help Displays Error Codes TroubleshootingTrouble Remedy − Electrical Diagram 193 264-A Circuit Diagram For Welding Power Source 575 Volt Models 206 318-A − Parts List Dia Part Description Quantity Mkgs Optional Service Your distributor also givesSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s