Miller Electric Invision 456MP 498 463, 130 684 561 482, 140 705 624 496, 150 720 687 508, 576

Page 37

Program 15 −− .035 Silicon Bronze −− Argon

IPM	Trim		Peak Amp	Background Amp	Freq.	Pulse Width	Starting Amps

120	0		280	37	42	1.30	501

183	10		331	54	57	1.40	540

246	20		371	68	72	1.50	582

309	30		402	77	93	1.60	610

372	40		421	87	108	1.70	642

435	50		442	96	119	1.80	663

498	60		463	108	130	1.90	684

561	70		482	115	140	2.00	705

624	80		496	122	150	2.10	720

687	90		508	127	160	2.20	730

750	100		520	131	170	2.30	737


		Program 16 −− .045 Metal Core −− Recommended Gases: Argon/CO2
			Gases: Argon/CO2 mixes up to 20% CO2
IPM	Trim		Peak Amp	Background Amp	Freq.	Pulse Width	Starting Amps

100	0		376	42	60	1.70	476

165	10		409	51	95	1.80	511

230	20		440	65	115	1.90	540

295	30		465	75	140	1.95	568

360	40		480	82	155	2.00	582

425	50		496	89	170	2.10	596

490	60		512	96	185	2.20	614

555	70		527	101	195	2.25	628

620	80		543	105	205	2.30	645

685	90		560	112	217	2.40	660

750	100		576	120	230	2.50	677


		Program 17 −− .052 Metal Core −− Recommended Gases: Argon/CO2
			Gases: Argon/CO2 mixes up to 20% CO2
IPM	Trim		Peak Amp	Background Amp	Freq.	Pulse Width	Starting Amps

50	0		360	30	35	1.90	600

120	10		421	54	75	2.00	649

190	20		461	72	105	2.10	698

260	30		491	91	125	2.25	751

330	40		512	105	145	2.40	800

400	50		531	120	165	2.50	800

470	60		545	127	180	2.60	800

540	70		564	138	190	2.70	800

610	80		576	143	202	2.80	800

680	90		588	148	214	2.90	800

750	100		600	150	225	3.00	800

OM-193 267 Page 33

Image 37

Contents Processes OM-193 267RDescription File MIG GmawFrom Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-193 267 Duty Cycle and Overheating SpecificationsCV Mode CC Mode Dimensions and WeightVolt-Ampere Curves 394 mmSelecting a Location ARC Welding can cause Electromagnetic Interference Weld Output Terminals and Selecting Cable Sizes350 ft 400 ft Put terminals Remote 14 Receptacle Information Connecting Weld Output CablesHz Three Phase Electrical Service GuideVolts AC Duplex Receptacle and Circuit Breakers Input VoltageSelecting Input Voltage For Models With Optional Ground Current Sensor Connecting Input PowerFor All Models = GND/PE Always connect grounding conductor firstFront Panel Controls Power SwitchMeter Functions Mode Meter Reading At Idle Meter Reading While WeldingExample Displays Synergic Controls and Overview Turn Output Adjust control to set arc length toExample ControlsPress Increment or Press Increment or Decrement button until MIG appearsStick appears Setup Screens Setting Arc Length Choosing Pulse Programs and Setting ParametersChoosing Pulse Program Choosing Adaptive Or Non AdaptiveOM-193 267 Overview of Programs Programs 150 652 342 538 369 600 138 449 206 484 125 624 274 512170 674 410 562 191 698 478 574145 550 354 430 320 441 156 345 472 222 371 120 511 288 402155 589 420 454 165 631 486 470240 336 120 258 550 160 270 649 200 298106 702 280 367 122 720 320 400705 180 291 652 220 312 663 260 338300 362 723130 684 561 482 498 463140 705 624 496 150 720 687 508230 541 451 674 498 705 140 515 741 185 527132 800 275 552 150 800 320 562Do not remove case when blowing out inside of unit Routine MaintenanceBlowing Out Inside of Unit Months802 314 / Ref Ref. ST-801 718 / Ref. ST-801 536-A Voltmeter/Ammeter Help Displays Troubleshooting Error CodesTrouble Remedy − Electrical Diagram 193 264-A Circuit Diagram For Welding Power Source 575 Volt Models 206 318-A − Parts List Dia Part Description Quantity Mkgs Optional Your distributor also gives ServiceSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s