Miller Electric EXTREME 360 manual SOCKET/WRENCH Selection Table Standard Metric

Page 37

Notes

SOCKET/WRENCH SELECTION TABLE				SOCKET/WRENCH SELECTION TABLE
	(U.S. STANDARD)				(METRIC)

Specifications		Socket or Wrench Size		Specifications		Socket or Wrench Size

Bolt	Decimal	Bolt	Nut	Bolt	U.S.
Bolt	Decimal			Bolt	Decimal	Bolt	Nut
Diameter	Equivalent			Diameter	Decimal	Bolt	Nut
Diameter	Equivalent			Diameter	Equivalent
					Equivalent

1/4 in	.250 in	3/8 in	7/16 in	6 mm	.2362 in	10 mm	10 mm

5/16 in	.3125 in	1/2 in	9/16 in	8 mm	.3150 in	14 mm	14 mm

3/8 in	.375 in	9/16 in	5/8 in	10 mm	.3937 in	17 mm	17 mm

7/16 in	.4375 in	5/8 in	3/4 in	12 mm	.4724 in	19 mm	19 mm

1/2 in	.500 in	3/4 in	13/16 in	14 mm	.5512 in	22 mm	22 mm

9/16 in	.5625 in	7/8 in	7/8 in	16 mm	.6299 in	24 mm	24 mm

5/8 in	.625 in	15/16 in	1 in	18 mm	.7087 in	27 mm	27 mm

3/4 in	.750 in	1-1/8 in	1-1/8 in	22 mm	.8661 in	32 mm	32 mm

7/8 in	.875 in	1-5/16 in	1-5/16 in	24 mm	.9449 in	36 mm	36 mm

1 in	1.000 in	1-1/2 in	1-1/2 in

Image 37

Contents Processes OM-229 409EDescription 2007−11Page Table of Contents Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-229 409 CC Mode SpecificationsCV Mode − Introduction60% Duty Cycle Duty Cycle And OverheatingMinutes Welding Minutes Resting OverheatingDimensions And Weight − InstallationSelecting a Location =GND/PE Earth Ground Connecting 1-Phase Input PowerConnecting 3-Phase Input Power Single-Phase Input Voltage Electrical Service GuideInput Amperes At Rated Output Min Grounding Conductor Size In AWG/KcmilARC Welding can cause Electromagnetic Interference Weld Output Receptacles And Selecting Cable Sizes350 ft 400 ft Put terminals Socket Information Remote 14 Receptacle InformationOperation Optional Gas Valve Operation And Shielding Gas ConnectionGas flow starts with remote contac- tor on − Operation Power SwitchFront Panel Controls Mode Meter Reading At Idle Meter Reading While Welding Mode Switch SettingsMode Switch Setting Process Output On/Off Control Meter FunctionsStick Start Procedure Lift-Arc TIG ProcedureLow OCV Stick Do not remove case when blowing out inside of unit − Maintenance & TroubleshootingBlowing Out Inside Of Unit Voltmeter/Ammeter Help Displays TroubleshootingStart Your Professional Welding Career Now Circuit Diagram − Electrical Diagram211 328-F Parts Assembly − Parts ListPLG1 PLG13 174 Knob, Pointer .840 Dia X .250 Id W/Spring Clip−.21 212 Start Your Professional Welding Career Now SOCKET/WRENCH Selection Table Standard Metric Material Thickness Gauge Warranty Owner’s Record

SOCKET/WRENCH SELECTION TABLE

(U.S. STANDARD)

(METRIC)