Miller Electric SRH-503 ARC Rays can burn eyes and skin, Welding can cause fire or explosion

Page 6

ARC RAYS can burn eyes and skin.

Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly off from the weld.

DWear a welding helmet fitted with a proper shade of filter to protect your face and eyes when welding or watching (see ANSI Z49.1 and Z87.1 listed in Safety Standards).

DWear approved safety glasses with side shields under your helmet.

DUse protective screens or barriers to protect others from flash and glare; warn others not to watch the arc.

DWear protective clothing made from durable, flame-resistant mate- rial (leather and wool) and foot protection.

WELDING can cause fire or explosion.

Welding on closed containers, such as tanks, drums, or pipes, can cause them to blow up. Sparks can fly off from the welding arc. The flying sparks, hot workpiece, and hot equipment can cause fires and

burns. Accidental contact of electrode to metal objects can cause sparks, explosion, overheating, or fire. Check and be sure the area is safe before doing any welding.

DProtect yourself and others from flying sparks and hot metal.

DDo not weld where flying sparks can strike flammable material.

DRemove all flammables within 35 ft (10.7 m) of the welding arc. If this is not possible, tightly cover them with approved covers.

DBe alert that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas.

DWatch for fire, and keep a fire extinguisher nearby.

DBe aware that welding on a ceiling, floor, bulkhead, or partition can cause fire on the hidden side.

DDo not weld on closed containers such as tanks, drums, or pipes, unless they are properly prepared according to AWS F4.1 (see Safety Standards).

DConnect work cable to the work as close to the welding area as practical to prevent welding current from traveling long, possibly unknown paths and causing electric shock and fire hazards.

DDo not use welder to thaw frozen pipes.

DRemove stick electrode from holder or cut off welding wire at contact tip when not in use.

DWear oil-free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes, and a cap.

DRemove any combustibles, such as a butane lighter or matches, from your person before doing any welding.

FLYING METAL can injure eyes.

DWelding, chipping, wire brushing, and grinding cause sparks and flying metal. As welds cool, they can throw off slag.

DWear approved safety glasses with side shields even under your welding helmet.

OM-2236 Page 2

BUILDUP OF GAS can injure or kill.

D Shut off shielding gas supply when not in use.

D Always ventilate confined spaces or use approved air-supplied respirator.

HOT PARTS can cause severe burns.

DDo not touch hot parts bare handed.

DAllow cooling period before working on gun or

torch.

MAGNETIC FIELDS can affect pacemakers.

D Pacemaker wearers keep away.

D Wearers should consult their doctor before going near arc welding, gouging, or spot welding operations.

NOISE can damage hearing.

Noise from some processes or equipment can damage hearing.

DWear approved ear protection if noise level is high.

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under high pressure. If damaged, a cylinder can explode. Since gas cylinders are normally part of the welding process, be sure to treat them carefully.

DProtect compressed gas cylinders from excessive heat, mechani- cal shocks, slag, open flames, sparks, and arcs.

DInstall cylinders in an upright position by securing to a stationary support or cylinder rack to prevent falling or tipping.

DKeep cylinders away from any welding or other electrical circuits.

DNever drape a welding torch over a gas cylinder.

DNever allow a welding electrode to touch any cylinder.

DNever weld on a pressurized cylinder − explosion will result.

DUse only correct shielding gas cylinders, regulators, hoses, and fit- tings designed for the specific application; maintain them and associated parts in good condition.

DTurn face away from valve outlet when opening cylinder valve.

DKeep protective cap in place over valve except when cylinder is in use or connected for use.

DRead and follow instructions on compressed gas cylinders, associated equipment, and CGA publication P-1 listed in Safety Standards.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents OM-2236 ProcessesDescription From Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers Identifie un message de sécurité particulier − Consignes DE Sécurité − À Lire Avant UtilisationLES Pièces Chaudes peuvent cau- ser des brûlures graves LE Soudage peut causer un incen- die ou une explosionLES Particules Projetées peu- vent blesser les yeux LE Bruit peut affecter l’ouïe’EMPLOI Excessif peut Faire Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser LES Pièces Mobiles peuvent cau- ser des blessuresPrincipales normes de sécurité Information sur les champs électromagnétiquesConsignes relatives aux stimulateurs cardiaques General Precautionary Label − DefinitionsDo Not Lift Nameplate Safety SymbolsInput Connection Label ? a− Installation SpecificationsDuty Cycle And Overheating Volt-Ampere Curves Selecting a LocationMovement Location And Airflow Be careful when placing or moving unit over uneven surfaces Dimensions And WeightsDimensions w/Running Gear And Lift Eye Tipping150 ft 200 ft 250 ft 300 ft 350 ft Selecting And Preparing Weld Output CablesWeld Cable Sizes 45 m 60 m 70 m 90 m 105 m 120 mConnecting To Weld Output Terminals Electrical Service GuidePlacing Jumper Links Connecting Input Power Welding Power Source Input Power ConnectionsDisconnect Device Input Power Con- nections − Operation ControlsElectrode/Amperage Selector Disconnect power before maintaining Months − Maintenance & TroubleshootingRoutine Maintenance Fuse F1Troubleshooting Table Trouble RemedyOM-2236 − Electrical Diagram Circuit Diagram− Parts List Main AssemblyHINGE,CONT Polyolefin Copolymer 2.000 L W/.125H THERMOSTAT,NC Open 135C Close 135C W/INSUL Leads Service SupportOwner’s Record Miller Electric Mfg. Co

SRH-503 specifications

The Miller Electric SRH-503 is a cutting-edge multiprocess welding machine designed to meet the diverse needs of professional welders. This versatile machine combines various welding processes, including MIG, TIG, and stick welding, making it a perfect choice for fabricators, artists, and maintenance professionals. With its robust build quality and user-friendly design, the SRH-503 provides excellent performance for both light and heavy-duty applications.

One of the standout features of the SRH-503 is its advanced inverter technology, which allows for efficient and stable arc performance. This technology not only improves energy efficiency but also enhances the machine's ability to handle a wide range of materials, from thin sheet metals to thicker plates. The inverter system ensures a consistent welding output, which is essential for achieving high-quality welds in various positions.

Another significant characteristic of the Miller Electric SRH-503 is its dual voltage capability. Operating on either 230V or 460V, the SRH-503 provides flexibility for working in diverse environments and power sources. This feature is particularly beneficial for welders who need to switch between different job sites or who want the convenience of using the machine in various locations.

The SRH-503 is equipped with a digital display that provides real-time feedback on settings and performance. This makes it easier for welders to adjust parameters for optimal results. The machine also includes advanced controls that allow for precise adjustments of welding voltage and amperage, ensuring that users can fine-tune their settings based on the specific needs of their project.

Built with durability in mind, the Miller Electric SRH-503 features a sturdy enclosure that can withstand the rigors of job site conditions. The compact design increases portability, making it easy to transport between locations. Additionally, the machine's intuitive interface allows for quick setup and adjustment, which saves valuable time in fast-paced working environments.

In summary, the Miller Electric SRH-503 is a state-of-the-art welding machine that brings together versatility, advanced technology, and user-friendly features. With its inverter system, dual voltage capability, intuitive controls, and rugged design, this machine is well-suited for professionals seeking reliable and efficient welding solutions. Whether for industrial, fabrication, or repair applications, the SRH-503 delivers exceptional performance and quality.
Top Page Image Contents